Rothoblaas - Wood screws and connectors Sida 184
Kommersiell Kunderbjudande **Toppförsäljare från RothoBlaas Deutschland
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
STATIC VALUES | BEECH LVL CHARACTERISTIC VALUES EN 1995:2014 TENSION(1) steel tension total thread withdrawal(2) geometry L b A d1 LVL steel without pre-drilling hole with pre-drilling hole d1 eq. d1 L b A min Rax,k Rax,k Rtens,k [mm] [mm] [mm] [mm] [mm] [kN] [kN] [kN] 6 140 130 150 32,76 22,62 6 180 170 190 42,84 29,58 6 220 210 230 52,92 36,54 6 260 250 270 63,00 43,50 8 200 190 210 63,84 44,08 8 240 230 250 77,28 53,36 8 280 270 290 90,72 62,64 8 320 310 330 104,16 71,92 7 9 18,00 32,00 TENSION(1) steel tension partial thread withdrawal (2) geometry L b Sg A Sg A d1 LVL steel without pre-drilling hole with pre-drilling hole d1 eq. d1 L b Sg A min Rax,k Rax,k Rtens,k [mm] [mm] [mm] [mm] [mm] [mm] [kN] [kN] [kN] 6 140 130 55 75 13,86 9,57 6 180 170 75 95 18,90 13,05 6 220 210 95 115 23,94 16,53 20,01 7 9 6 260 250 115 135 28,98 8 200 190 85 105 28,56 19,72 8 240 230 105 125 35,28 24,36 8 280 270 125 145 42,00 29,00 8 320 310 145 165 48,72 33,64 18,00 32,00 NOTES: (1) The connector design resistance is the lowest between the timber side design resistance (Rax,d) and the steel side resistance (Rtens,d). Rax,d = min Rax,k kmod γM Rtens,k γM2 (2) The axial thread withdrawal resistance Rax,90,k was calculated considering a 90° angle between the grain and the connector and for a fixing length of b. 184 | VGZ HARDWOOD | STRUCTURES (3) The design sliding strength of the joint is either the timber-side design strength (R ) or the steel design strength (R ), whichever is lower. V,d tens,d 45° RV,d = min RV,k kmod γM Rtens,k 45° γM2 (4) The connector tensile strength was calculated considering a 45° angle between the fibres and the connector.
369 Sidor | Gäller till 04/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
