fischer Rögzítőrendszerek főkatalógusa Pagina 165
Commercieel klantenaanbod**Beste verkopers van Fischer
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
Superbond dynamic FSB dyn · Chemical fixings Accessories Filling set Filling sets for subsequent filling of the annular gap Match Sales unit Item No. [pcs] Item 3 Filling set M 12 537218 FIS A/RG M 12 10 Filling set M 16 537219 FIS A/RG M 16 10 Filling set M 12 R 557875 FIS A/RG M 12 R 10 Filling set M 16 R 557876 FIS A/RG M 16 R 10 Filling set M 20 R 557877 FIS A/RG M 20 R 10 Filling set M 24 R 557878 FIS A/RG M 24 R 10 Filling set M 20 R push-through 557879 FIS A/RG M 20 R 10 Filling set M 24 R push-through 557880 FIS A/RG M 24 R 10 Loads Superbond dynamic with Superbond mortar FIS SB and threaded rod FIS A resp. RG M Design values for cyclic fatigue loading¹) of a single anchor normal concrete of strength class C20/25²). For the design the complete current assessment ETA-19/0501 has to be considered. Material/ surface FIS A M 16 FIS A M 20 FIS A M 24 Minimum member thickness Installation torque Non-cracked concrete Design values of tension (∆NEd,max) and shear loads (∆VEd,max); minimum spacing (smin) and edge distances (cmin) with reduced loads Design values of tension (∆NEd,max) and shear loads (∆VEd,max); minimum spacing (smin) and edge distances (cmin) with reduced loads hef hmin Tinst ∆NEd,max³) ∆VEd,max³) smin³) cmin³) ∆NEd,max³) ∆VEd,max³) smin³) cmin³) [mm] [mm] [Nm] [kN] [kN] [mm] [mm] [kN] [kN] [mm] [mm] 8.8 70 100 40 3.0 2.0 55 55 4.5 2.0 55 55 8.8 110 140 40 4.5 2.0 55 55 4.5 2.0 55 55 8.8 240 270 40 4.5 2.0 55 55 4.5 2.0 55 55 R-70 70 100 40 3.0 2.7 55 55 4.8 2.7 55 55 R-70 110 140 40 4.9 2.7 55 55 4.9 2.7 55 55 R-70 240 270 40 4.9 2.7 55 55 4.9 2.7 55 55 8.8 80 120 60 4.8 3.7 65 65 8.4 3.7 65 65 8.8 125 170 60 8.4 3.7 65 65 8.4 3.7 65 65 8.8 320 360 60 8.4 3.7 65 65 8.4 3.7 65 65 R-70 80 120 60 4.8 4.9 65 65 8.4 4.9 65 65 R-70 125 170 60 8.8 4.9 65 65 9.2 4.9 65 65 R-70 320 360 60 9.2 4.9 65 65 9.2 4.9 65 65 R-70 90 140 120 7.1 7.6 85 85 12.4 7.6 85 85 R-70 170 220 120 14.3 7.6 85 85 14.3 7.6 85 85 R-70 400 450 120 14.3 7.6 85 85 14.3 7.6 85 85 R-70 96 160 150 7.4 11.0 105 105 11.8 11.0 105 105 R-70 210 270 150 20.2 11.0 105 105 20.6 11.0 105 105 R-70 480 540 150 20.6 11.0 105 105 20.6 11.0 105 105 Type FIS A M 12 Effective anchorage depth Cracked concrete ¹) The design values of the cyclic fatigue loading apply for load cycles > 108 in accordance with design method I acc. to TR061 - for unknown static lower load. If the static lower load is known and / or for lower number of load cycles higher load values are possible. The partial safety factors as regulated in the design standard are considered. As a single anchor counts e.g. an anchor with a spacing s ≥ 3 x hef . The given load values apply for anchorages in dry and wet concrete and temperatures in the base material up to 50 °C (resp. short-term up to 80 °C) and drill hole cleaning acc. to assessment. ²) For higher concrete strength classes up to C50/60 higher permissible loads may be possible, see assessment. The concrete is assumed to be standard-reinforced. ³) In the case of combinations of tension loads, shear loads, bending moments with reduced or minimum spacing and edge distances (anchor groups) the design must be carried out in accordance with the provisions of the complete assessment. 165
684 Pagina’s | Geldig tot 12/2025 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.