GEDORE Automotive KLANN Main catalog General Repairs Page 58
Commercial customer offer**Products from catalog page
Steering System/Geometry (Pat. e.g. US-Patent 6,546,610) KL-0250-40 Extractor for Clamping Bolt and Ball Joint, Audi A4/VW Passat KL-0250-40 Suitable for Audi A4 (until 2000)/VW Passat front axle (until 2005). Designed to remove the upper wishbone pivot pin from the steering knuckle clamping bore. Removing the upper clamping bolt and the two pivot pins from the steering knuckle has always presented mechanics and technicians with problems, especially when components are heavily corroded/seized in place. Not only is the usual technique using hammer, welding torch, angle grinder and drift time-consuming and arduous, but there is also a risk of damaging steering knuckles, pivot pins and wishbone struts. 2 The KL-0250-40 extractor with its proper pressure unit enables the quick and professional extraction of the hex clamping bolt and pivot pins. The tool is suitable for both right-hand and left-hand wheel suspensions. Example of use: • Mount tool with pressure unit to steering knuckle (with pressure drift I inserted). • Drive hex nut by means of an impact wrench and push back the hex clamping bolt. The loosening process takes place with a loid noise. • Extract hex clamping bolt with the pressure unit in 3 working stages. For this, insert the pressure drifts II + III one after another. • Pull out hex clamping bolt completely. In case it is still not possible to extract the entire hex clamping bolt, use the supplement pressure drift set KL-0250-402 to press it out completey. • Remove hex nut. Completely remove pressure drift so that the clamping bore is clear. • Using the pressure spindle, push out both pivot pins from the clamping bore. Advantages: • High cost savings. • Substantial time savings of approximately 2-3 hours. • No risk of damage to suspension components. Scope of Delivery: KL-0250-40 Extractor for Clamping Bolt and Ball Joint, Audi A4/VW Passat Part No. KL-0250-4001 KL-0250-4002 KL-0250-4005 KL-0250-4011 KL-0250-4012 KL-0250-4013 KL-0250-4014 KL-0250-4015 Description Tool Body Thread Adaptor (with large bore) Pressure Screw, M10x1.25x95mm Housing Pressure Drift I (Length 78mm) Nut Pressure Drift II (Length 98mm) Pressure Drift III (Length 118mm) KL-0250-402 Qty 1 1 1 1 1 1 1 1 Technical Data: Weight: 2.4kg KL-0250-402 Upgrade Pressure Drift Set Used to press the hex clamping bolt completely out of the clamping bore. Scope of Delivery: KL-0250-402 Upgrade Pressure Drift Set Part No. KL-0250-4016 KL-0250-4017 KL-0250-4018 KL-0250-403 Description Pressure Drift IV (Lenght 138mm) Pressure Drift V (Length 158mm) Pressure Drift VI (Length 178mm) Qty 1 1 1 KL-0250-403 Pressure Drift Puller The pressure drift puller KL-0250-403 enables pressure drifts to be pulled out of the tool body. 2-14 (58) Copyright GEDORE Automotive GmbH, Germany formerly
580 Pages | Valid until 12/2025 | Previous page | Next page
Choose your language
Legal issues
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
Request form for special products
The ToolTeam® Procurement Service
Are you looking for products that are shown in the catalogue but cannot be purchased directly online?Our procurement service will be pleased to make you a non-binding and individual offer.