Pneumax - Hauptkatalog Page 740
Commercial customer offer**Top sellers from Pneumax GmbH
Modular FRL Series 1700 Steel line - Size 3 Ordering code Filter regulators S V 173 C E S Overall automatic drain version (A.D.) Overall manual drain version 71 Ch. 17 28.5 1/8” NPT Connection relieving V Ch. 17 C G1/2” 1/4” - 1/2” NPT Connections IN/OUT 76 91 22 31,5** 259.5 14.5 223.5 S M6 N°2 Front holes N°2 Rear holes 65* M5 N°4 Holes side IN N°4 Holes side OUT 31,5** G 140 104 2 T 71 1/8” NPT Automatic drain connection * = BOWL REMOVAL MAXIMUM HEIGHT ** = ONLY FOR M VERSION O EF = EPDM-FDA * no additional letter required Technical characteristics Construction characteristics - Body, adjust. mechanism, AISI 316L stainless steel and caseback intern. components Maximum inlet pressure (standard version) 20 bar - AISI 316 stainless steel adjustment springs. Maximum inlet pressure (automatic drain version) 16 bar - Fixing screws, adjustment screws and locknut in A4 (AISI 316) stainless steel. Maximum inlet pressure (reduced orifice automatic drain version) - Filter-pressure regulator diaphragm with over-pressure drain (Relieving). Temperature (standard version) -30°C +80°C - Low hysteresis rolling diaphragm. Temperature (low temperature version) -50°C +80°C - Balanced system. Temperature (low temperature version -60°C) -60°C +80°C - Manual or automatic condensed drain. Temperature (high temperature version) -5°C +150°C Temperature (automatic and reduced orifice drain version) Temperature (EPDM-FDA version) Note The pressure must be always regulating while increasing. For a more precise regulation and higher sensibility, the use of a regulator with a pressure range as close as possible to the regulated pressure is recommended. Flow rate chart Pressure gauge connections 2110 (gr.) 3 Bowl capacity 25 cm Assembly position Vertical 1/2 NPT - G1/2" 1/4 NPT - G1/4" 5 4 3 2 1 0 1000 2000 3000 Flow rate Q [dm³/min] (ANR) 4000 5000 60 Inlet pressure (bar) Reg. 0-12 bar Pressure regulator Stainless steel line have been designed to withstand a 60 Bar maximum inlet pressure. Maximum regulated outlet pressure is 20 Bar. For performance details please refer to diagram alongside. 50 Reg. 0-4 bar 40 30 Reg. 0-8 bar 20 2 | 166 Reg. 0-2 bar 0 1 2 -5°C +70°C 1/8” NPT Weight 6 0 10 bar -40°C +100°C Inlet pressure 10 bar - Reg. 0-12 bar 7 Pressione a valle (bar) Air Service UnitS 1/8” NPT Pressure gauge connections G T O VERSION S = Standard surface finishing F = Clean profile M = Modular assembly version CONNECTIONS A = 1/4” NPT B = 1/2” NPT D = G1/2” FILTER PORE SIZE A = 5 µm - 316 stainless steel B = 20 µm - 316 stainless steel C = 50 µm - 316 stainless steel D = 5 µm - HDPE E = 20 µm - HDPE F = 50 µm - HDPE PRESSURE RANGE A = 0-2 bar B = 0-4 bar C = 0-8 bar D = 0-12 bar TYPE = Standard* N = Without relieving OPTIONS = Standard* L = Low temperature Z = Low temperature (-60 °C) H = High temperature S = Automatic drain SR = Reduced orifice automatic drain 3 4 5 6 7 8 9 10 11 12 13 Max. regulated pressure (bar) Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice
1106 Pages | Valid until 06/2025 | Previous page | Next page
Choose your language
Legal issues
The manufacturer is exclusively responsible for the content, price and article details of the products and offers presented in the catalogues. Subject to technical and optical changes by the manufacturer and errors excepted.
Request form for special products
The ToolTeam® Procurement Service
Are you looking for products that are shown in the catalogue but cannot be purchased directly online?Our procurement service will be pleased to make you a non-binding and individual offer.