fischer Rögzítőrendszerek főkatalógusa Strana 258
Nabídka komerčních zákazníků **Nejlépe prodávané z Fischer
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Bez dopravy
Nail anchor FNA II · High performance steel anchors Technical data Setting tools for FNA II FNA II S-SDS FNA II S-SBO FNA II S-H Sales unit Item No. fits anchor FNA II S-SDS 061547 for all FNA II with nail head The ideal setting tool for the serial installation with SDS-plus adapter for driving in FNA II with nail head using a hammer drill. FNA II S-SBO 061548 for all FNA II with nail head For a power saving and fast installation to be placed on the drill. 1 FNA S-H 095990 for FNA II with metric thread M6 E.g. for the fixing of installation of mounting rails. Chuck with outer diameter of 15 mm for the installation of FNA II M6 by hand. 1 Item 4 1 Loads Nail anchor FNA II Permissible loads for a single anchor¹) for multiple use of redundant non-structural applications* in normal concrete C20/25 up to C50/60²). For the design the complete current assessment ETA-06/0175 has to be considered. Cracked and non-cracked concrete Material/ surface Type Effective anchorage depth Minimum member thickness Maximum installation torque Permissible load (Fperm); minimum spacing (smin) and edge distances (cmin) with reduced loads hef hmin Tinst,max Fperm³) smin cmin [mm] [mm] [Nm] [kN] [mm] [mm] FNA II 6 x 25 gvz 25 80 - 1.4 40 40 FNA II 6 x 30 gvz 30 80 - 2.4 40 40 R 30 80 - 2.4 40 40 HCR 30 80 - 2.4 40 40 FNA 6 x 25 M6 gvz 25 80 4 1.4 40 40 FNA 6 x 30 M6 gvz 30 80 4 2.4 40 40 R 30 80 4 2.4 40 40 HCR 30 80 4 2.4 40 40 FNA II 6 x 30 M8 gvz 30 80 4 2.4 40 40 FNA II 6 x 25 OE gvz 25 80 - 0.7 40 40 * In addition to the load table above, the following must be considered for multiple fastening of non-structural redundant systems: A multiple fixing (redundant system) according to EN 1992-4 and CEN/TR 17079 is defined by - at least 3 fixing points (per attached element) with at least one anchor at each fixing point and a permissible load per fixing point of 1.4 kN - or by at least 4 fixing points with at least one anchor each fixing point and a permissible load per fixing point of 2.1 kN - Additionally, it has to be proven that the stiffness of the attached element shall be large enough to ensure that in case of excessive slip or failure of a fastener the load on this fastener or fixing point can be transferred to neighbouring fixing points without significantly violating the requirements on the attached element in the serviceability and ultimate limit state. For further details see EN 1992-4 section 7.3 and CEN/TR 17079. ¹) Design according to EN 1992-4:2018 (for static resp. quasi-static loads). The partial safety factors for material resistance as regulated in the ETA as well as a partial safety factor for load actions of γL = 1.4 are considered. ²) For concrete strength class C12/15 see ETA. ³) Valid for tensile load, shear load and oblique load under any angle. In the case of combinations of tensile, shear loads and bending moments, the design must be carried out in accordance with the provisions of the complete ETA and the provisions of the EN 1992-4:2018. 258
684 Stránky | Platí do 12/2025 | Previous page | Další stránka
Vyberte si jazyk
Legální problémy
Výrobce je výhradně zodpovědný za obsah, cenu a detaily produktů a nabídek uvedených v katalozích. Technické a optické změny výrobce a chyby jsou vyhrazeny.
Formulář žádosti o speciální produkty
Služba nákupu ToolTeam®
Hledáte produkty, které jsou uvedeny v katalogu, ale nelze je zakoupit přímo online?Naše služba nákupu vám ráda zpracuje nezávaznou a individuální nabídku.