Rothoblaas - Wood screws and connectors Sida 201
Kommersiell Kunderbjudande **Toppförsäljare från RothoBlaas Deutschland
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
GEOMETRY LF D2 D1 H BF h L SPLATE Washer VGU945 VGU1145 VGU1345 VGS screw diameter d1 [mm] 9,0 11,0 13,0 VGS screw pre-drilling hole diameter(1) dV [mm] 5,0 6,0 8,0 Internal diameter D1 [mm] 9,7 11,8 14,0 External diameter D2 [mm] 19,0 23,0 27,4 Base length L [mm] 31,8 38,8 45,8 Base heigth h [mm] 3,0 3,6 4,3 Global heigth H [mm] 23,0 28,0 33,0 Slotted-hole length LF [mm] Slotted-hole width BF [mm] Steel plate thickness SPLATE [mm] min. 33.0 max. 34.0 min. 14.0 max. 15.0 min. 3.0 max. 12,0* min. 41.0 max. 42.0 min. 17.0 max. 18.0 min. 4.0 max. 15,0* min. 49.0 max. 50.0 min. 20.0 max. 21.0 min. 5.0 max. 15,0* (1) Pre-drilling valid for softwood. thicker plates it is necessary to realize a countersink in the lower part of the steel plate. For VGS screw-lengths L > 300 mm a Ø5 pre-drill is recommended. The assembly must be performed so as to guarantee that the stress is evenly distributed among all the installed VGU washers. (*) For CODES AND DIMENSIONS VGU WASHER CODE JIG VGU TEMPLATE screw dV [mm] [mm] pcs CODE washer dh [mm] dV pcs VGU945 VGS Ø9 5 25 JIGVGU945 VGU945 5,5 5 1 VGU1145 VGS Ø11 6 25 JIGVGU1145 VGU1145 6,5 6 1 VGU1345 VGS Ø13 8 25 JIGVGU1345 VGU1345 8,5 8 1 HSS WOOD DRILL BIT CODE dh [mm] [mm] LOCKING RING FOR HSS BITS dV TL SL [mm] [mm] [mm] pcs F1599105 5 150 100 1 F1599106 6 150 100 1 F1599108 8 150 100 1 CODE LE LT dV dint dext [mm] [mm] [mm] pcs dint F2108005 5 5 10 10 F2108006 6 6 12 10 F2108008 8 8 16 10 dext HELPS WITH INSTALLATION The JIG VGU template makes it easy to prepare a 45° angle pre-drill, thus facilitating subsequent tightening of the VGS screws inside the washer. A pre-drill length of at least 20 mm is recommended. STRUCTURES | VGU | 201
369 Sidor | Gäller till 04/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
