Röhm Main Catalogue Clamping Technology Sida 724
Kommersiell Kunderbjudande **Toppförsäljare från RÖHM
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Determining the required gripping force of a power chuck Power-operated clamping devices The two components FsBo and Fvax give the resultant force FR FR = FSBo2 + Fvax2 The amount of the resultant force FR can be obtained directly from Table 7. Intermediate values will have to be determined by interpolation. Power-operated clamping devices Cutting force FsBo [kN] Resultant force FR KN Table 7 50 45 40 35 30 25 20 15 10 9,0 8,0 7,0 6,0 5,0 4,5 4,0 3,5 3,0 2,5 2,0 1,8 1,6 1,4 1,2 1,0 0,8 FSBo FR Fvax 6,9 6,1 5,7 5,3 4,9 4,6 4,3 4,0 5,8 2,0 1,8 1,7 1,6 1,4 2,3 2,1 2,0 1,8 1,7 1,6 2,6 2,4 2,3 2,1 2,0 1,9 1,8 1,2 1,4 1,6 3,1 2,7 2,5 2,4 2,3 2,2 2,1 2,0 3,2 2,8 2,7 2,6 2,4 2,3 2,2 2,2 1,8 2,0 4,3 3,9 3,5 3,2 3,1 3,0 2,9 2,8 2,5 5,4 5,0 4,6 4,2 3,9 3,6 3,5 3,4 3,0 3,5 8,1 7,2 6,4 6,0 5,7 5,3 5,0 4,7 4,0 10,3 9,4 8,6 7,8 7,0 6,7 6,4 6,1 5,8 8,3 7,5 6,7 6,4 6,0 5,7 5,4 5,1 4,5 5,0 16,2 11,7 10,8 10,0 9,2 8,5 7,8 7,5 7,2 6,0 16,6 11,2 11,4 10,6 9,9 9,2 7,0 17,0 12,8 12,0 11,3 10,6 10,0 8,0 9,0 21,9 17,5 13,5 12,7 12,0 32,3 26,9 27,7 22,4 23,3 18,0 19,2 14,1 15,6 13,5 12,8 37,7 33,1 28,7 24,4 20,5 17,2 43,1 38,5 34,0 29,7 25,6 21,9 48,5 43,9 39,4 35,0 30,8 26,9 53,9 49,2 44,7 40,3 36,1 32,0 28,3 10,0 12,0 14,0 16,0 18,0 20,0 25,0 Feeding force Fvax [kN] Place resultant force FR for drilling in solid material in the known formula for determining the required gripping force Fspz: Fspz = FR . Sz . μsp dz dsp where: Fspz = gripping force required for a given job with the chuck stationary. FR = resultant force of cutting force and feeding force Chucking ratio dz = dsp cutting dia. chucking dia where dz = drill dia. 2 μsp = chucking coefficient (friction between jaw and workiece) Sz = safety factor II and III Continue the calculation - from determination of the initial gripping force Fspo to determination of operating power and the pressure required - exactly as described in Section A) Turning, II) and III). 6210 www.eshop.roehm.biz 55,9 51,5 47,2 43,0 39,1 35,4 58,3 54,1 50,0 46,1 42,4 61,0 64,0 57,0 53,2 30,0 35,0 40,0
892 Sidor | Gäller till 12/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
