Röhm Main Catalogue Clamping Technology Sida 718
Kommersiell Kunderbjudande **Toppförsäljare från RÖHM
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Determining the required gripping force of a power chuck Power-operated clamping devices A Turning I) Calculating the required gripping force Fspz The gripping force required depends on the Type of work to be performed. The cutting force on the turning tool has three basic components: Main cutting force Fs - feeding force Fv - passive force (static force) Fp. During turning, the feeding force Fv and the passive force (static force) Fp are mainly absorbed by the jaw faces in contact with the seated workpiece. The remaining main cutting force produces a moment (Fs x dz/2) which must be absorbed by the chuck and transmitted by friction at the clamping point. The moment produced by the main cutting force during turning determines the gripping force required: Fs . S z sp F spz = (1) dz d sp . where: Fspz = gripping force required for a specific job with the chuck stationary = main cutting force Fs chucking ratio dz = dsp μsp Sz machining diameter chucking = cucking coefficient (friction between jaw and workpiece) = safety factor The feeding force and passive components, Fv and Fp, are not included in this formula. If necessary for extreme conditions, they are included in the safety factor Sz. Power-operated clamping devices The main cutting force Fs is calculated from feed, depth of cut and material. where: s= feed, mm/rev. t= depth of cut, mm kc = specific cutting force, kN/mm2 Fs (2) = s . t . kc The product s x t (feed.depth of cut) = chip cross-section (can be obtained from Table 1). Determining the chip cross section [mm2] Table 1 Feed (mm) Depth of cut t (mm) 2 0,16 0,20 0,25 0,32 0,40 0,50 0,63 0,80 1,0 1,25 1,60 0,64 0,8 1,0 1,26 1,6 2,0 2,5 3,2 3 0,75 0,96 1,2 1,5 1,89 2,4 3,0 3,75 4,8 4 5 6 7 8 9 10 12 0,8 1,0 1,28 1,6 2,0 2,52 3,2 4,0 5,0 6,4 0,8 1,0 1,25 1,6 2,0 2,5 3,15 4,0 5,0 6,25 8,0 0,96 1,2 1,5 1,96 2,4 3,0 3,78 4,8 6,0 7,5 9,6 1,12 1,4 1,75 2,24 2,8 3,5 4,41 5,6 7,0 8,75 11,2 1,28 1,6 2,0 2,56 3,2 4,0 5,04 6,4 8,0 10,0 12,8 1,44 1,8 2,25 2,88 3,6 4,5 5,67 7,2 9,0 11,25 14,4 1,6 2,0 2,5 3,2 4,0 5,0 6,3 8,0 10,0 12,5 16,0 1,92 2,4 3,0 3,84 4,8 6,0 7,56 9,6 12,0 15,0 19,2 The specific cutting force kc as a function of feed can be obtained from Table 2. 6204 www.eshop.roehm.biz
892 Sidor | Gäller till 12/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
