PFERD Tools Main Catalogue Sida 92
Kommersiell Kunderbjudande **Toppförsäljare från PFERD
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Milling, drilling and countersinking tools General information Custom-made products 2 If you cannot find the solution for your particular application in our comprehensive catalogue range, we are happy to produce milling tools to meet your wishes and requirements. Our sales representatives and technical advisers will be happy to assist you in analyzing your task. Your specifications and wishes, drawings relating to cuts, shank diameters, special lengths, special shapes and coatings can thus be taken into account. Resharpening PFERD offers resharpening of tungsten carbide burrs, subject to a minimum resharpening quantity of 25 units (unmixed items). Regrinding of HSS rotary cutters or tungsten carbide burrs with a shank diameter of 3 mm is not recommended for economic reasons. In each case, our production specialists will decide whether resharpening makes sense from an economic point of view and is technically feasible. The following cuts can be resharpened (only applies to a shank diameter of 6 and 8 mm): ■ Cut 1 ■ ALU ■ Cut 3 ■ TITANIUM ■ Cut 3 PLUS ■ TOUGH ■ Cut 4 ■ TOUGH-S ■ Cut 5 ■ MICRO ■ INOX Safety notes ■ For safety reasons, the maximum permitted rotational speed indicated must never be exceeded. Wear a dust mask! Tighten the bolts! 4 Nm Wear eye protection! Wearing protective gloves is recommended. Handle the tool drive with both hands. Do not use if damaged! Wear gloves! Observe the recommended rotational speed, especially when using burrs with long shanks! Do not use for cutting! Observe the contact angle of 5–60° (ALUMASTER HSD-F)! CE-marked Burr shapes Page Catalogue 4 2 ZYA Cylindrical shape ZYA BS Cylindrical shape with drill cut ZYAS/HSS A-ST Cylindrical shape with end cut ZYA ZBS Cylindrical shape with centre drill
724 Sidor | Gäller till 12/2025 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
