GEDORE Automotive KLANN BMW Range brochure Sida 11
Kommersiell Kunderbjudande **Produkter från katalogsidan
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
(Code 3279642) KL-0033-16 Pair of Pressure Plates, Size 0A KL-0033-16 Universal application. Particularly suitable for use on Mercedes-Benz E-Class (W211, W212), C-Class (W204, on the rear axle), GLA (X156), GLK (X204); Ford Focus III (MK3); BMW 1 Series (E81); VW Passat (B8/3G). The pair of pressure plates, in conjunction with the necessary accessories, allows you to quickly and safely remove and install coil springs on wishbone and independent, multi-link suspensions in situ on the vehicle.The unique 3-point safety interlock mechanism and the special anti-rotation profile prevent the pressure plates from twisting during the compression process and, thus, the coil spring from coming loose and falling off the spring compressor. Necessary Accessories (included in KL-0033-10 E): KL-0033-100 Compact Compressor Base Body, IN19LK8-140 Bit Socket, 8mm waf Technical Data: For spring Ø from: For spring Ø up to: Gradient of pressure plate to 240°: 80mm (inside)) 110mm (outside) 6mm Scope of Delivery Part No. KL-0033-1601 KL-0033-1602 Description Pressure Plate, Size 0A, with interlock mechanism Pressure Plate, Size 0A, with anti-rotation profile Qty 1 1 (Code 3275205) KL-0033-300 E Holding-Down Tool Kit, in a Foam Insert KL-0033-300 E Universally applicable to wishbone and independent, multi-link suspension systems as found in vehicles from VW-Audi, Seat, Porsche, Mercedes, BMW, Ford and in many more. Essential tool for use on the rear axle of VW-Audi, Porsche and Mercedes-Benz vehicles. For example: Audi A4 (8K), A5 (8T), A6 (C6), Q5 (8R), Q7 (4M); Seat Exeo (3R); VW Touareg; Porsche Cayenne (PO536), Macan; Mercedes-Benz E-Klasse (W211, W212), C-Klasse (W204), GLA (X156), GLK (X204); etc. The holding-down tool kit is intended to ease the removal and installation of coil springs on wishbone and independent, multi-link suspensions. Particularly recommended for use with our KL-0033-10 E Compact Internal Coil Spring Compressor. Insert the holding-down tool between the upper control arm and the vehicle body. Then, pre-tighten it slightly. The tool is designed to keep the suspension in position while the coil spring is being compressed. This reduces the compression travel and greatly facilitates the removal of the spring. Tool Storage System: KL-4990-9224 Plastic Storage Case Technical Data: Drive: Diameter of support: Clamping range (short adjusting nut): Clamping range (long adjusting nut): 22mm waf Ø 40/50mm 80 - 113mm 105 - 138mm E With holdingdown clamp Scope of Delivery Part No. KL-0033-3001 KL-0033-3002 KL-0033-3003 A KL-0033-3004 KL-0033-3005 KL-0033-3090-1 Description Support Bracket Support, Ø 50mm Support, Ø 40mm Adjusting Nut, short Adjusting Nut, long Foam Insert Qty 1 1 1 1 1 1 E Copyright GEDORE Automotive GmbH, Germany Without holdingdown clamp 11
32 Sidor | Gäller till 12/2025 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.