Ganter Norm Standard Parts - Catalogue Sida 1648
Kommersiell Kunderbjudande **Toppförsäljare från Ganter Norm
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Universal Joints with Friction Bearing Extract Stainless Steel, Single or Double 2 Bore code B Without keyway K With keyway V With square 1 d1 3 4 4 l1 l2 Type EG Type DG 34 Bore s H10 Square 6 V 6* 16 8 V 8* 22 10 V 10 * 25 12 V 12* 56 86 32 16 V 16* 68 105 42 20 V 20 * 82 128 50 25 V 25* 108 163 16 d 2 H7 3 l3 l4 t +1 Max. assembly length of the shaft 56 17 22 8 40 62 20 22 11 48 74 24 26 12 28 30 13 34 37 16 41 46 18 54 55 26 3.5 EG Single, friction bearing DG Double, friction bearing 3.4 Type 3.6 5 3.3 3.2 3.1 DIN 808 * not available from stock, requires a minimum order quantity Stainless steel AISI 304 • Keyway JS9 DIN 6885 Page 2078 • Cross Holes GN 110.1 Page 2081 • ISO Fundamental Tolerances Page 2151 • Stainless Steel Characteristics Page 2166 • RoHS On request • With other or unequal bores NI Since the moveable parts are not surface treated, i.e. not case hardened, the possibilities of application of these universal joints are much more limited compared to the ones made of standard steel. Therefore, the guide lines for the selection of universal joints with friction bearing Page 1644 according to the diagram may be applied at a limited extent only. Rotational speeds over 200 min may become critical. For continuous use of the stainless steel universal joints, ample lubrication is very important. This achieved by fitting the joint with a grease filled gaiter GN 808.1 Page 1653. 3.7 • Information 3.8 6 The order example refers to universal joints with equal bores both ends d2 or s. 3.9 Specification How to order 1 2 3 4 5 6 DIN 808-32-B16-105-DG-NI 1 d1 2 Bore code 3 d 2 (s) 4 l 2 (l1) 5 Type 6 Material 3.6 Moving, Transferring, Connecting with Shafts and Joints | Page 1647
2210 Sidor | Gäller till 12/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
