Ganter Norm Standard Parts - Catalogue Sida 1574
Kommersiell Kunderbjudande **Toppförsäljare från Ganter Norm
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Electrical specifications 3.1 GN 650.5 Oil Level Indicators continued Oil level monitoring Temperature monitoring Max. switching voltage / Max. switching current: 250 V AC / 10 A 48 V DC / 5 A 3.2 Max. switching voltage / 150 V AC, 100 V DC / 1 A (NO) Max. switched current: 150 V AC, 150 V DC / 2 A (NC) Max. switching capacity: 10 W (NO) / 20 W (NC) Connector plug: Protection class: Cable gland: Cable cross-section: DIN EN 175301-803 type C IP 65 PG 7, for cable Ø from 6 to 7 mm 2 x 1,5 mm² 3.3 Oil level and temperature monitoring 3.4 Caution: Magnet fields impair the proper function! Assembly sequence for cable connection 2. Push the contact holder out off the connector casing. 3.5 1. Loosen the mounting screw and pull off the connector plug. 4. Push the contact holder back into the connector casing and tighten the cable gland for strain relief grip / seal. 3.6 3. Loosen the cable gland, feed the cable through the connector casing and connect to the contact holder. 3.7 5. Push the connecting plug over the connecting contacts of the oil level indicator and secure with mounting screw. For the best possible sealing effect of the O-rings, do not overtighten the screws (max. 12 Nm). Recommended roughness of the sealing flange surface Ra = 3 μm. 3.5 Controlling, Venting, Sealing of Liquids and Gases | Page 1573 3.9 Two tapped holes M12 are required for mounting the oil level indicator GN 650.5. If nuts are used for mounting, two Ø 12.5 bore holes are required. 3.8 Assembly instructions
2210 Sidor | Gäller till 12/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
