Ganter Norm Standard Parts - Catalogue Sida 1495
Kommersiell Kunderbjudande **Toppförsäljare från Ganter Norm
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
GN 148 Leveling Feet Determining the Suitable Leveling Foot Terms Interference frequency [Hz]: is the frequency emanating from a machine, e.g. the machine main shaft speed [rpm]. Static load F [N]: is the load acting on each vibration-damping element (leveling foot). Degree of insulation [%]: is the measure for absorbing the interference frequency (dampening). Compression s [mm]: is the change in height of the damping element (spring excursion). Stiffness R [N/mm]: is the load which causes a damping element to be compressed by 1 mm (spring rate). Determining the suitable leveling foot and the maximum degree of insulation First, the static load F for each leveling foot must be determined. For well arranged leveling feet and the resulting even distribution of the load F, the static load is calculated using the following equation: Weight force of the machine [N] = Static load F [N] / per leveling foot Number of leveling feet Once the static load F has been calculated, select a leveling foot from the table. Please note that the static load F should be as close as possible to the static load capacity, but without exceeding it. The associated stiffness R of the selected leg is also shown in the table. The actual compression is then calculated using the equation below. Static load F [N] / per leveling foot Stiffness R [N/mm] = Actual compression s [mm] Starting from the actual compression s calculated, the maximum degree of insulation as factor of the interference frequency can now be read in the above chart. To optimise the maximum degree of insulation, change the number of feet such that the static load F of each leveling foot is as close as possible below a static load capacity value given in the table. This will increase the compression s which, in turn, improves the degree of insulation. In general, medium and high frequencies can be very well insulated with an adequate compression. Page 1494 | 3.4 Installing, Lifting, Damping with Leveling Feet, Lifting Gear and Rubber Elements
2210 Sidor | Gäller till 12/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
