Ganter Norm-Elemente - Neuheiten Sida 212
Kommersiell Kunderbjudande **Toppförsäljare från Ganter Norm
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Aluprofile Technische Daten GN 10i / GN 11i Mechanische Daten (in Pressrichtung) Werkstoff: AlMgSi 0,5 F25 (EN AW – 6063) Lieferzustand: warmausgehärtet • Eloxal: E6EV1 (naturfarben), Schichtdicke: 10 μm • Formabweichungen nach DIN EN 12020-2 • Zugfestigkeit Rm min. 245 N/mm² Fließgrenze Rp0,2 min. 195 N/mm² Dichte 2,7 kg/dm³ • Linearer Ausdehnungskoeffizient 23,6x10-6 1/k • Elastizitätsmodul E ≈ 70.000 N/mm² • Härte ≈ 75HB -2,5/187,5 • • • • Zulässige Zugbelastung der Nut n Rastermaß Profiltyp 6 30 leicht 8 40 leicht 8 40 schwer F N* in N mit Nutenstein GN 50i Form N Form V 3000 3000 - Form S 7500 5500 - 15000 15000 19000 * abhängig von der Gewindegröße des Nutensteins Querschnittseigenschaften Wx , Wy Ix, Iy It A m = = = = = axiales Widerstandsmoment gegen Biegung Flächenmoment 2. Grades gegen Biegung Flächenmoment 2. Grades gegen Torsion Querschnittsfläche längenbezogene Masse GN 10i Profiltyp leicht s1 s2 n Rastermaß Biegeachse x-x I x in cm 4 30 30 6 30 2,9 30 60 6 30 21,2 60 60 6 30 39,5 Biegeachse y-y W x in cm 3 I y in cm 4 1,94 7,07 13,2 4,55 2,9 5,54 39,5 It W y in cm 3 in cm 4 1,94 3,69 13,2 0,3 3,18 21,5 40 40 8 40 9,1 9,1 4,55 1,36 40 80 8 40 70,2 17,6 16,8 8,45 9,94 80 80 8 40 130,1 33,2 130,1 33,2 80,8 A in cm 2 3,43 6,13 10,0 6,47 m≈ in kg/m 0,93 1,65 2,7 1,75 11,3 3,08 19,3 5,17 A m≈ GN 10i Profiltyp schwer s1 s2 n Rastermaß Biegeachse x-x I x in cm 4 40 16 8 40 1,06 Biegeachse y-y W x in cm 3 I y in cm 4 1,25 6,95 6,75 13,9 It W y in cm 3 in cm 4 3,37 6,95 0,97 1,88 in cm 2 4,15 9,05 in kg/m 1,12 40 40 8 40 13,9 40 80 8 40 101,0 25,2 26,7 13,4 18,8 16,5 4,51 2,45 80 80 8 40 187,8 46,9 187,8 46,9 128,4 26,7 7,2 n Rastermaß Biegeachse x-x A m≈ GN 11i Profiltyp leicht s1 40 210 s2 40 8 40 I x in cm 4 W x in cm 3 I y in cm 4 Biegeachse y-y It W y in cm 3 in cm 4 in cm 2 in kg/m 9,63 4,96 4,96 6,79 1,83 9,63 3.7 Verbinden, Aufbauen mit Klemm- und Verbindungselementen 5,41
412 Sidor | Gäller till 12/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
