fischer ETICS-Fixings EWI catalogue Sida 31
Kommersiell Kunderbjudande **Toppförsäljare från Fischer
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Screw fixings termoz 6H The efficient countersunk ETICS fixing for board materials Fixing of wooden soft fibre boards on solid wood Attachment of polystyrene boards on OSBpanel VERSIONS CERTIFICATES ▪ A2 stainless steel screw BUILDING MATERIALS ▪ ▪ ▪ ▪ ▪ 3 28 MDF boards OSB boards Chipboard Gypsum fibreboard Solid wood ADVANTAGES APPLICATIONS FUNCTIONING ▪ The pre-assembled ETICS fixing guarantees safe fixing into the substrate. ▪ The special geometry under the head of the anchor roughens the surface during the setting process and provides a torque-reduced penetration into the insulation. ▪ The use of the setting tool 6H enables a clean fixing. Optionally, the setting tool CS can be used in combination with a special bit. ▪ The minimum screw-in depth of 24 mm provides quick installation. Pre-drilling is not necessary. ▪ For insulating material thicknesses up to 300 mm. ▪ The countersunk mounting guarantees plaster surfaces without any markings. ▪ Attachment of ETICS insulating boards on wooden substructures ▪ Flush installation in ETICS insulating materials e.g. polystyrene and mineral wool ▪ Flush-to-surface installation in pressure-resistant insulation boards ▪ The special setting tool 6H is used for countersunk installation. This setting tool 6H enables a precise positioning and fast installation of the fixing. The countersunk hole is covered with a suitable insulation closing plug which ensures a homogeneous surface. ▪ By rotating the disc of the setting tool 6H by 180°, it can be used for the flush-to-surface installation. This allows the exact positioning of the anchor plate on the insulation surface. The screw opening is covered by the included plug.
71 Sidor | Gäller till 12/2025 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
