Euroboor - Main Catalog Sida 10
Kommersiell Kunderbjudande **Toppförsäljare från Euroboor BV
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Power protection The power protection feature is two-fold; it consists of both power fluctuation protection and power surge protection. Special safety components built into the electronics of the machine make it more reliable in situations where power supply can be of varying quality due to factors: - Around the workplace, for example caused by switching on high power or unreliable electrical devices, a broken circuit breaker or faulty wiring - Outside the workplace, for example caused by an instable power grid or lightning A machine with this feature is able to cope with standard rated voltage and frequency fluctuations ranging from: - 110 Volt to 130 Volt and 45 Hz to 65 Hz, or - 220 Volt to 240 Volt and 45 Hz to 65 Hz reducing the probability of breakdown and minimizing down-time and repair cost. Power fluctuation protection When the frequency is too high (above 65 Hz) or too low (below 45 Hz), the motor will not start. If the frequency of the power supply falls outside the range during your drilling job, the motor will shut off automatically. The machine will work again normally when the normal frequency has been restored.* Power surge protection Beyond the rated voltage, a machine with this feature is able to cope with voltage spikes up to 4,000 Volt (1-2μs)*, which could be caused by nearby welding activities. Depending on the height of the spike, it may be necessary to replace built-in fuses, the control unit or the power switch, but other valuable parts like the motor and magnet will be protected. Worn-out carbon brush Regular carbon brush Automatic shut-off carbon brush Overload protection To ensure safe use and longer lifetime of the motor the machine profits by overload protection. While you are using the machine there are different types of load levels, which correlate Carbon brushes with the feed pressure. Once you go from close to overload to exceeding the overload limit the machine will automatically stop the motor. The carbon brushes on the magnetic drilling machine are equipped with two protective features. The purpose of both Smart Restart When the motor is in overload, the Smart Restart torque control technology ensures trouble-free continuation of features is to schedule timely service and avoid additional costs by unexpected downtime or unnecessary part replacement. your drilling job. When the feed pressure is reduced, the machine’s electronics recognise the reduction and the motor continues within a few seconds. Carbon brush wear indicator On the motor housing you will find an integrated Overheat protection LED light. Under normal circumstances this light is off. The LED light will start burning RED when the carbon To prevent damage, machines with this feature are equipped brushes are worn to a level where it is advised to replace with a sensor which will shut off the motor automatically when them. the temperature of the field coil exceeds 100˚ C - 105˚ C. Automatic shut-off When the carbon brushes are actually worn to a level *Disclaimer: Euroboor is not liable for any damage caused to the machine due to electrical problems in the workplace. Above mentioned protection is not guaranteed in all cases of voltage spikes and/ or frequency fluctuations. Euroboor accepts no liability when it comes to the power protection not functioning or functioning poorly. 10 where replacement is needed, the motor will be shutoff automatically. This prevents the armature from being damaged. Once shut off, the LED-indicator is no longer lit.
140 Sidor | Gäller till 12/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.