Dynabrade - Industrial Katalog Sida 306
Kommersiell Kunderbjudande **Toppförsäljare från Dynabrade Europe Sarl
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
306 Up to 4" ( 100 mm) diameter Greater than 1/8" ( 3 mm) thick Type 1 Reinforced Straight Wheels NOTE: Intended for general reference use only. Straight relieved flange 1/3 of wheel diameter minimum 6" (150 mm) maximum Straight relieved flange matching diameter to Driving Flange Required on both sides of wheel. Loose blotters must be replaces when mounting a new wheel Requires retaining Spindle Nut Recommend wheel retainer hardware – 1/3 of wheel diameter may be smaller to fit the depressed area of the wheel. Requires centering boss to extend within wheel center hole – – – Additional Safety 1/3 of wheel diameter may be smaller to fit the depressed area of the wheel. Requires centering boss to extend within wheel center hole Smaller diameter than the Drive Flange to fit the depressed area of the wheel Outer Flange Required between flange and wheel Not required Requires a special support adapter that extends beyond the raised hub and contacts the wheel Straight unrelieved flange 1/3 of wheel diameter minimum Greater than Ø5" (125 mm) with 7/8" (22 mm) Center hole Not required A special support adapter may be used or straight unrelieved flange 1/3 of wheel diameter minimum Not required Requires a special support adapter that extends beyond the raised hub and contacts the wheel Ø3" (75 mm) and Ø4" (100 mm) with 3/8" (10 mm) Center hole Alternate flanging for wheels less than or equal to Ø5" (125 mm) with Ø5/8" (16 mm) or Ø7/8" (22 mm) Center hole Blotters Driving Flange Abrasive Size Type 11 Flaring Cup Wheels Type 27 Reinforced Depressed Center Wheels, Flap Wheels Abrasive Type Mounting Features PRODUCT & SAFETY INFORMATION Spindle Adapter Outer Flange Driving Flange Safety Guard Retaining Washer Retaining Screw Reinforced Type 27 Wheel Outer Flange Driving Flange Spindle Reinforced Type 27 Wheel Outer Flange Driving Flange Spindle Reinforced Type 27 Wheel Outer Flange Driving Flange Spindle Hood Diagram Lip Feature Lip Feature Lip Feature 1/8" Max. Exposure Blotter Blotter Reinforced Type 1 Wheel Spindle Nut Type 11 Flared Cup Wheel Lip Feature Adjustable Skirt (Shell) Blotter Driving Flange Straight - Unrelieved Adapter Safety Guard Safety Guard Safety Guard Proper Mounting Procedure Always refer to ANSI B7.1, B186.1 and EN 792 for detailed requirements. • A guard cover is not required • Lip Feature must extend past face of wheel • Lip Feature • 180° minimum Operator Protection • Adjustable skirt to within 1/8" (3 mm) of the wheel face • Adjustable skirt (shell) • 180° minimum Operator Protection • Lip Feature must extend past face of wheel • Lip Feature • 180° minimum Operator Protection • Lip Feature must extend past face of wheel • Lip Feature • 180° minimum Operator Protection • Lip Feature must extend past face of wheel • Lip Feature • 180° minimum Operator Protection Guard Requirements Safety Guidelines For Various Abrasive Power Tools
316 Sidor | Gäller till 07/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
