Dynabrade - Industrial Katalog Sida 106
Kommersiell Kunderbjudande **Produkter från katalogsidan
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Type 11 Cup Wheel Grinders 1/2" AIR LINE PAGE 237 ACCESSORIES Air-Powered Vertical Grinders, 6" Diameter PAGE 233 FOR TYPE 11 CUP WHEELS AND WIRE BRUSHES For Fast Weld and Stock Removal, Rust and Scale Removal, Heavy Deburring 6" (152 mm) diameter NOT INCLUDED • Each model accepts optional Type 11 Cup Wheels, 6" (152 mm) diameter. Covers more area in less time! • Governor-controlled air motor maintains tool RPM under heavy load. • Overspeed shut-off feature ensures maximum operator safety. • Motor is gearless with less wearable parts, ensuring reduced maintenance and less downtime. • Insulated tool handle minimizes cold air transmission to the hand. Handle position is adjustable for operator comfort. • All models include safety-lock throttle lever. • For peak performance, use of optional 95870 Air Hose (1/2" diameter) is recommended. Model 53233 Model 53233 Model 53233 Model 53233 shown powering 6" dia. Type 11 Cup Wheel. Tool also accepts Wire Brushes. GRINDERS 2 hp (1,491 W), 6,000 RPM Model 53243 3 hp (2,237 W), 6,000 RPM Cup Wheel Not Included IMPORTANT: Speed of tool must not exceed maximum operating speed of accessory. Always wear eye, face & body protection. Model Number Motor hp (W) Motor RPM Sound Level Maximum Air Flow SCFM (L/Min) Hose I.D. Size Inch (mm) Air Inlet Thread Spindle Thread Weight Pound (kg) Length Inch (mm) Height Inch (mm) 53233 2 (1,491) 6,000 83 dB(A) 80 (2,265) 1/2 (13) 1/2" NPT 5/8"-11 Male 10.5 (4.7) 9.5 (241) 7 (178) 53243 3 (2,237) 6,000 82 dB(A) 89 (2,520) 1/2 (13) 1/2" NPT 5/8"-11 Male 11.1 (5) 9.5 (241) 7.5 (190) Tune-Up Kit: 53233 – No. 96552; 53243 – No. 96553 • Additional Specifications: Air Pressure 90 PSIG (6.2 Bar) Safety Procedures for Grinding Wheels Operator Should Comply with OSHA and ANSI B7.1 Safety Regulations • DO check all wheels for cracks or other damage before mounting. • DO NOT use wheels which have been dropped or otherwise damaged. • DO check machine speed against the established maximum safe operating speed marked on wheel. • DO NOT use a grinding wheel that has rated speed less than the speed of the grinder • DO use mounting blotters when supplied with wheels. • DO NOT use excessive pressure when mounting wheel between flanges. Tighten nut only enough to hold wheel firmly. • DO be sure wheel hole, threaded or unthreaded, fits machine arbor properly and that flanges are clean, flat and of the proper type for the wheel you are mounting. • DO NOT use heavy side grinding pressure on any Type 1 straight wheel or thin Type 27 wheel. • DO always run wheel in a protected area at least one minute before grinding. • DO use wheel guard furnished with machine. • DO NOT handle machine carelessly. Stop wheel on work and use racks or hooks to support machine when not in use. • DO always wear protective safety glasses and additional eye and face protection if required. • DO NOT use relieved or recessed flanges with threaded hole cup wheels, cones or plugs. • DO employ dust controls and/or protective measures appropriate to the material being ground. • DO NOT mount more than one wheel on a single arbor. Permission for reprint of form 4968T granted by UAMA 106
316 Sidor | Gäller till 07/2026 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.