Bosch Air tools for industry catalog Sida 8
Kommersiell Kunderbjudande **Toppförsäljare från Bosch Blau
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
8 | Drills, rotary hammers | Selection guide 1 Selection guide Drills Drills Part number Choosing a drill is based on two No-load speed (rpm) Page criteria: ▶ the drilling diameter Cutting speed (m/min): ▶ the recommended cutting 120-watt drill controlled speed of the material you are 0 607 154 101 working on 3,200 10 (see page 14). 400-watt drill In the table, the optimal cutting speeds and drilling diameters for some common materials are allocated to the individual drill uncontrolled 0 607 161 100 2,560 10 0 607 161 102* 2,560 10 0 607 161 101 1,200 10 0 607 161 103* 1,200 10 models. 180-watt drill These recommendations are based on the speeds for HSS twist uncontrolled 0 607 153 520 3,700 10 0 607 153 523* 3,700 10 drill bits. If nothing is specified, the required drilling diameter is outside the capacity of the standard 400-watt drill uncontrolled 0 607 161 500 2,560 10 0 607 161 504* 2,560 10 The table shows which drill bit 0 607 161 501 1,200 10 sizes the individual models can 0 607 161 505* 1,200 10 chuck. 0 607 161 502 800 10 0 607 161 506* 800 10 ally been assigned the maximum 0 607 161 503 640 10 drilling diameters for steel, deter- 0 607 161 507* 640 10 accept and the drilling speeds. The individual tools have addition- mined in tests. * with keyless chuck To ensure that a sufficient cutting speed is always achieved, some materials should be pre-drilled as of the following drilling diameter: ▶ Steel up to 600 N/mm2 as of 8 mm ▶ Steel over 600 N/mm2 as of 6 mm ▶ Cast iron up to 180 N/mm2 as of 10 mm ▶ Cast iron up to 300 N/mm2 as of 8 mm
116 Sidor | Gäller till 06/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
