AMF Catalogue Single and multiple clamping system Sida 7
Kommersiell Kunderbjudande **Toppförsäljare från AMF Spannsysteme
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
exkl. Frakt
Collet attachment outside clamping No. 6375ZA Collet attachment outside clamping Collet attachment made of high-strength aluminium, hard anodised. With locking bolt made of tempered steel, burnished. Order no. 428656 Size 20 dia. D dia. D1 dia. D2 149 140 23 H H1 H2 H3 50 25 10 10 Material Clamping stroke Ø [mm] Weight EN AW 7075 0,3 880 [g] Design: Collet attachments are always supplied with locking bolt. Application: The collet attachment is fastened using fastening kit 6375BA (observe torque specifications) on the base element 6375M. To secure the workpiece contour, the collet attachment must be clamped with the locking bolt. Then the workpiece contour is milled into the collet attachment with a minimum clamping depth of 2 mm. Then the locking bolt is removed, and the workpiece can be clamped. The collet attachment can be milled off to a height of H1, allowing new workpiece contours to be introduced. The maximum workpiece diameter is specified in the table with D1. Advantage: - Clamping of delicate and thin-walled workpieces - Free-form clamping - The workpiece is clamped without distortion due to the radially even clamping force imposed on it - Multiple insertion of different workpiece contours possible Note: The collet attachment must always be clamped with the workpiece or locking bolt. To remove the vertical play between the collet attachment and base element, light pretensioning must be applied by actuating the clamping stud after the workpiece is inserted. Subject to technical alterations. ANDREAS MAIER GmbH & Co. KG ∙ Phone: +49 711 5766-0 ∙ Web: www.amf.de Single and multiple clamping SyStemS 7
64 Sidor | Gäller till 12/2024 | Previous page | Nästa sida
Välj ditt språk
Juridiska frågor
Tillverkaren ansvarar exklusivt för innehållet, priset och artikeldetaljerna för produkterna och erbjudanden som presenteras i katalogerna. Med förbehåll för tekniska och optiska ändringar av tillverkaren och undantag för fel.
Formulär för specialprodukter
ToolTeam® upphandlingstjänst
Letar du efter produkter som visas i katalogen men inte kan köpas direkt online?Vår upphandlingstjänst kommer med glädje att ge dig ett icke-bindande och individuellt erbjudande.
