Klingspor main catalogue Abrasive, cutting-off & grinding discs Página 388
Oferta para clientes comerciais**Vendedores mais populares de Klingspor
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
excl. o transporte
Small abrasive mop Technical Glossary Application recommendations ‣ The small abrasive mop can be used with flexible shaft grinders, die grinders (pneumatic, electric) or drilling machines. ‣ The small abrasive mop’s optimum performance is achieved at a cutting rate between 20 – 25 m/s. By observing these speeds, the product will perform at its most economical as regards tool wear, stock removal, surface finish and thermal load of the workpiece. Factors influencing the grinding result Stock removal Ø Height [mm] h [mm] Maximum operating speed [m/s]* RPM [1/min] L0= 0 mm L0= 10 mm 10 ≤ 15 40 76,300 55,000 35,000 15 ≤ 25 40 50,500 37,000 28,000 20 ≤ 20 40 38,150 28,600 21,900 25 ≤ 15 40 30,500 22,900 17,500 30 ≤ 15 40 25,400 19,000 14,600 40 ≤ 20 40 19,000 14,300 10,900 50 ≤ 30 40 15,200 11,400 8,700 ≤ 40 40 12,700 9,500 7,300 50 32 10,150 7,900 6,300 ≤ 40 40 9,500 7,100 5,400 50 32 7,650 6,000 4,800 60 80 * for exposed shank length L0 = 0 mm An increase in stock removal should only occur as a result of using coarser grit and not as a result of increased tool / grinding pressure. L0 Steady increased tool / grinding pressure ‣ results in unnecessary tool wear and tear ‣ results in increased workpiece temperature load ‣ can result in tool failure Ø min. 20 mm Surface finish ‣ The wear of the outer edge of the grinding flaps results in the presentation of new sharp abrasive grain, which results in a uniform surface finish ‣ The surface roughness decreases through an increase in the cutting rate ‣ An increase in the tool / grinding pressure results in a coarser surface finish ‣ The small abrasive mop achieves a significantly smoother surface finish compared to that of a belt grinder Temperature load ‣ By reducing the tool / grinding pressure and the peripheral speeds the temperature load of the workpiece and the tool is reduced. 388 L0= 20 mm h Tool wear ‣ Tool wear is reduced by working with a lower grinding pressure. To ensure the optimal and most efficient use of a tool ‣ the maximum revolutions per minute may not be exceeded ‣ the fixing spindle length of the small abrasive mop in the mounting device must be at least 20 mm ‣ the set revolutions per minute may not be exceeded when using an exposed shaft length L0 (please refer to the table above) For additional information please refer to the safety information provided with the product.
440 Páginas | Válido até 12/2027 | Página anterior | Próxima página
Escolha a sua língua
Questões legais
O fabricante é exclusivamente responsável pelo conteúdo, pelo preço e pelos detalhes dos produtos e das ofertas apresentados nos catálogos. Sujeito a alterações técnicas e ópticas por parte do fabricante e com excepção de erros.
Formulário de pedido de produtos especiais
O serviço de aquisições de ToolTeam®
Está à procura de produtos que são mostrados no catálogo mas que não podem ser comprados diretamente online?O nosso serviço de aprovisionamento terá todo o prazer em fazer-lhe uma oferta individual e não vinculativa.