Rothoblaas - Plates and Connectors Strona 192
Oferta dla klientów komercyjnych**Najlepiej sprzedający się od RothoBlaas Deutschland
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
TCN200 - TCN240 | PARTIAL FASTENING PATTERNS FOR STRESS F2/3 In the presence of design requirements such as F2/3 stresses of different value or the presence of an intermediate HB layer (levelling mortar, sill or ground) between the wall and the supporting surface, partial fastening patterns can be adopted: FULL PATTERN PATTERN 4 PATTERN 3 PATTERN 2 PATTERN 1 Pattern 2 also applies in case of F4, F5 and F4/5 stresses . MAXIMUM HEIGHT OF THE INTERMEDIATE HB LAYER HB HB configuration on timber nv holes Ø5 [pcs] TCN200 TCN240 CLT C/GL HB max [mm] HB max [mm] nails screws nails screws LBA Ø4 LBS Ø5 LBA Ø4 LBS Ø5 • full pattern 30 36 20 30 32 10 • pattern 4 25 30 30 40 42 20 • pattern 3 20 24 40 50 52 30 • pattern 2 15 18 50 60 62 40 • pattern 1 10 12 60 70 72 50 The height of the H B intermediate layer (levelling mortar, sill or timber platform beam) is determined by taking into account the following regulatory requirements for fastenings on timber: • CLT: minimum distances according to ÖNORM EN 1995-1-1 (Annex K) for nails and ETA-11/0030 for screws . • C/GL: minimum distances for solid timber or glulam with horizontal fibres consistent with EN 1995-1-1 according to ETA considering a timber density of ρk ≤ 420 kg/m3 . TCN200 - TCN240 | VERIFICATION OF ANCHORS FOR CONCRETE FOR F2/3 STRESS Fastening elements to the concrete through anchors shall be verified according to the load acting on the anchor, which can be evaluated through the geometric parameters on the table (e) . Ey calculation eccentricities vary depending on the type of installation selected: 2 internal anchors (IN) or 2 external anchors (OUT) . The anchor group must be verified for: VSd,x = F2/3,d MSd,z = F2/3,d x ey,IN/OUT z x F2/3 ey 192 | TITAN N | PANELS AND BUILDING JOINTS y
576 Strony | Ważny do 04/2024 | Previous page | Następna strona
Wybierz swój język
Zagadnienia prawne
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
