KS Tools special tools for utility tools and transporters Strona 286
Oferta dla klientów komercyjnych**Najlepiej sprzedający się od KS Tools
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
SAC clutch removal 1. Select the appropriate centring pin depending on the pilot bearing diameter and screw onto the clamping mandrel with the receiving thread M8. 2. Equip the clamping mandrel with the appropriate clamping sleeve, depending on the hub diameter of the clutch disc. 3. Insert the fully equipped clamping mandrel (relaxed clamping sleeve) into the pilot bearing. 4. Guide the new clutch disc over the centring device and insert into the flywheel receptacle. Attention: It is important for an optimal guiding that the centring pin is close-fitting in the pilot bearing. 5. Now the clamping sleeve is braced in the hub of the clutch disc by securing the clamping mandrel with one hand and using the other hand to actuate the drive on the mandrel end so that the clamping sleeve spreads in the hub (finger tightening is sufficient). 6. Place the new clutch pressure plate on the flywheel (note centring pins). Select the matching threaded bolts and screw 3 threaded bolts into the flywheel hand-tight offset by 120°. Offset by 90° for 4-pitch! (e.g. Mercedes W169 A-class from MJ 2004). Attention: Always screw the short thread end into the flywheel. 7. Attention: Pressure plate does not abut! 8. Correct: Pressure plate abuts! 9. Insert the cover fastening screws into the open threaded receptacles of the flywheel and tighten. 286
528 Strony | Ważny do 07/2024 | Previous page | Następna strona
Wybierz swój język
Zagadnienia prawne
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
