Ganter Norm Standard Parts - Catalogue Strona 1644
Oferta dla klientów komercyjnych**Najlepiej sprzedający się od Ganter Norm
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
Universal Joints and Universal Joint Shafts 3.4 3.3 In order to obtain a smooth rotation, two single or one double universal joint is required. In such cases where minor irregularities in the movement are acceptable or where minor inclination angles are the norm, a single universal joint will do. 3.2 The single universal joints transfer the initial steady rotation as an irregular rotation because one revolution of the drive shaft using the single universal joint will cause the driven shaft to accelerate and decelerate twice. The extent of the irregularity depends on the operating angle ß. 3.1 Mounting Information 3.8 If the universal joint shafts are connected incorrectly, the irregular rotation of each joint is not compensated, but strengthened. This can destroy joint bearings and wedge profiles. For this reason, the markings of the universal joint shaft halves have to be opposite to each other when connecting them. 3.7 3.6 3.5 For a steady transfer of rotation, the inclination angles ß must be equal on both ends of the connecting shaft. For continuous operation of universal joints with friction bearings, adequate lubrication is essential. If drip lubrication is not possible, they should be lubricated at least once a day. It is also possible to fit the universal joint with a gaiter GN 808.1 which can be filled with oil or grease. 3.6 Moving, Transferring, Connecting with Shafts and Joints | Page 1643 3.9 Furthermore, the bearings must be as close as possible to the universal joints.
2210 Strony | Ważny do 12/2026 | Previous page | Następna strona
Wybierz swój język
Zagadnienia prawne
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
