Ganter Norm Standard Parts - Catalogue Strona 1574
Oferta dla klientów komercyjnych**Najlepiej sprzedający się od Ganter Norm
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
Electrical specifications 3.1 GN 650.5 Oil Level Indicators continued Oil level monitoring Temperature monitoring Max. switching voltage / Max. switching current: 250 V AC / 10 A 48 V DC / 5 A 3.2 Max. switching voltage / 150 V AC, 100 V DC / 1 A (NO) Max. switched current: 150 V AC, 150 V DC / 2 A (NC) Max. switching capacity: 10 W (NO) / 20 W (NC) Connector plug: Protection class: Cable gland: Cable cross-section: DIN EN 175301-803 type C IP 65 PG 7, for cable Ø from 6 to 7 mm 2 x 1,5 mm² 3.3 Oil level and temperature monitoring 3.4 Caution: Magnet fields impair the proper function! Assembly sequence for cable connection 2. Push the contact holder out off the connector casing. 3.5 1. Loosen the mounting screw and pull off the connector plug. 4. Push the contact holder back into the connector casing and tighten the cable gland for strain relief grip / seal. 3.6 3. Loosen the cable gland, feed the cable through the connector casing and connect to the contact holder. 3.7 5. Push the connecting plug over the connecting contacts of the oil level indicator and secure with mounting screw. For the best possible sealing effect of the O-rings, do not overtighten the screws (max. 12 Nm). Recommended roughness of the sealing flange surface Ra = 3 μm. 3.5 Controlling, Venting, Sealing of Liquids and Gases | Page 1573 3.9 Two tapped holes M12 are required for mounting the oil level indicator GN 650.5. If nuts are used for mounting, two Ø 12.5 bore holes are required. 3.8 Assembly instructions
2210 Strony | Ważny do 12/2026 | Previous page | Następna strona
Wybierz swój język
Zagadnienia prawne
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
