Eurotec catalogue fastening technology Strona 19
Oferta dla klientów komercyjnych**
Pokaż produkty
Najlepiej sprzedający się od Eurotec
946070
Poproś o wycenę
Oferta dla klientów komercyjnych**
946079
Poproś o wycenę
Oferta dla klientów komercyjnych**
946071
Poproś o wycenę
Oferta dla klientów komercyjnych**
945959
Poproś o wycenę
Oferta dla klientów komercyjnych**
975611
Poproś o wycenę
Oferta dla klientów komercyjnych**
110000
Poproś o wycenę
Oferta dla klientów komercyjnych**
964552
Poproś o wycenę
Oferta dla klientów komercyjnych**
975623
Poproś o wycenę
Oferta dla klientów komercyjnych**
946068
Poproś o wycenę
Oferta dla klientów komercyjnych**
954105
Poproś o wycenę
Oferta dla klientów komercyjnych**
200036
Poproś o wycenę
Oferta dla klientów komercyjnych**
110361
Poproś o wycenę
Oferta dla klientów komercyjnych**
110121
Poproś o wycenę
Oferta dla klientów komercyjnych**
945040
Poproś o wycenę
Oferta dla klientów komercyjnych**
200065
Poproś o wycenę
Oferta dla klientów komercyjnych**
945870
Poproś o wycenę
Oferta dla klientów komercyjnych**
200085
Poproś o wycenę
Oferta dla klientów komercyjnych**
945986
Poproś o wycenę
Oferta dla klientów komercyjnych**
954021
Poproś o wycenę
Oferta dla klientów komercyjnych**
499985
Poproś o wycenę
Oferta dla klientów komercyjnych**
954211
Poproś o wycenę
Oferta dla klientów komercyjnych**
964575
Poproś o wycenę
Oferta dla klientów komercyjnych**
975631
Poproś o wycenę
Oferta dla klientów komercyjnych**
800455
Poproś o wycenę
Oferta dla klientów komercyjnych**
944890
Poproś o wycenę
Oferta dla klientów komercyjnych**
800464
Poproś o wycenę
Oferta dla klientów komercyjnych**
945318
Poproś o wycenę
Oferta dla klientów komercyjnych**
800496
Poproś o wycenę
Oferta dla klientów komercyjnych**
945857
Poproś o wycenę
Oferta dla klientów komercyjnych**
945956
Poproś o wycenę
Oferta dla klientów komercyjnych**
903640
Poproś o wycenę
Oferta dla klientów komercyjnych**
945979
Poproś o wycenę
Oferta dla klientów komercyjnych**
946010
Poproś o wycenę
Oferta dla klientów komercyjnych**
904670
Poproś o wycenę
Oferta dla klientów komercyjnych**
904727
Poproś o wycenę
Oferta dla klientów komercyjnych**
954104
Poproś o wycenę
Oferta dla klientów komercyjnych**
954221
Poproś o wycenę
Oferta dla klientów komercyjnych**
905555
Poproś o wycenę
Oferta dla klientów komercyjnych**
964564
Poproś o wycenę
Oferta dla klientów komercyjnych**
905575
Poproś o wycenę
Oferta dla klientów komercyjnych**
Zobacz wszystkie produkty Eurotec
Deck construction and landscaping Wood decks a mistake that is frequently made is to have centre distances in the substructure that are too large. The most durable results are achieved if this clearance, and therefore the screw clearance in the lengthwise direction of the boards, is max. 60 cm. Please note that the installation information provided here is merely a recommendation and does not constitute binding assembly instructions. Every assembly job is subject to different performance requirements, e.g. locally applicable building regulations, and the tradesman carrying out the installation is responsible for compliance with these requirements. t our hin op« -St »Drill ng although deck/wood construction screws today have a suitable deflection angle, hardwoods that are placed directly on top of each other function as shearing modules that shear the screws off if the wood swells or shrinks. (Per board half = 3,5 mm displacement, this conforms to about the inside diameter of a screw with a 5 mm thread, which is the minimum that should be used with tropical woods). However, using a spacer (e.g. Dista-Leiste 2.0 or deck glider) between the substructure and deck board is very helpful here. This provides the screws with a possibility of bending in the direction of the working wood. The danger of shearing is greatly reduced. In addition, this clearance protects the wood from waterlogging at the support points. The ageing process is slowed down clearly. nki at a width of 140 mm, Bangkirai woods or other hardwood/tropical woods can swell or shrink by up to 7 mm, depending on the wood moisture. With direct screwing through the boards into the substructure we recommend using a pair of screws. If the board is fastened directly on the substructure and the board works from the centre by about 3,5 mm, this leads in some cases to the screws being sheared off. The hardwood/tropical wood does not allow the screw to absorb any movement because it can barely be compressed because of its own high density. In certain circumstances, screwing in the centre of the board might be deducted from this. Unfortunately, tropical woods have an extremely high internal stress, which leads to the boards twisting (dishing), which in most cases requires pairs of screws. Pil ot dril rsi Because of constantly occurring problems with the use of hardwood/tropical woods we want to point out some fundamental working guidelines that must be observed. However, we refer in general to the recommendations of your wood dealer, because there can be extreme fluctuations in the wood properties with the same wood type, above all with tropical woods. Bangkirai wood, for example, which is often used, can have very different properties, because the properties depend heavily on the source in each case. If the variety of wood properties within a range is ignored, this can lead to various problems with regard to screws breaking off. ling and cou nte Pilot-drilling is always better with problematic woods. These are above all hardwood/tropical woods, but also some coniferous woods that tend to crack easily, such as e.g. Douglas fir. Pilot drilling prevents the wood splitting. With regard to the edge distances make sure that there is at least 6 cm clearance to the end of the board. (Please note: because of the high internal stress the boards can also crack open later at the ends and in the middle. This also applies to thermally treated woods). 19
444 Strony | Ważny do 12/2024 | Poprzednia strona | Następna strona
Wybierz swój język
Zagadnienia prawne
Oferta skierowana jest wyłącznie do klientów biznesowych, firm, instytucji publicznych, handlowców i freelancerów. Wszystkie ceny w katalogach nie zawierają podatku VAT, kosztów wysyłki i ewentualnych dopłat.
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
Proszę wypełnić wszystkie pola obowiązkowe (podkreślone na czerwono)
keyboard_arrow_down
Proszę wypełnić wszystkie pola obowiązkowe (podkreślone na czerwono)
