ENERPAC - Bolting Tools Strona 127
Oferta dla klientów komercyjnych**Najlepiej sprzedający się od ENERPAC
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
wył. Wysyłkę
Tensioning Manufacturer’s rating of pressure and load are maximum safe limits. Good practice encourages using only 80% of these ratings! Tensioning Operation Tensioning permits the simultaneous tightening of multiple bolts; the tools are connected in sequence via a highpressure hose assembly to a single pump unit. This ensures each tool develops the exact same load and provides a uniform clamping force across the joint. This is especially important for pressure containing vessels requiring even gasket compression to affect a seal. General Procedure Set-up Using a 100% Tensioning Procedure All bolts are tensioned simultaneously. Step 1 Step 2 Step 1: The bolt Tensioner is fitted over the stud. Step 2: Hydraulic pressure is applied to the tensioner which then stretches the stud. Step 3: The Stud’s nut is wound down against the joint face. Step 4: Pressure is released and the tool removed. Step 3 Step 4 The bolt behaves like a spring, when the pressure is released the bolt is under tension and attempts to contract, creating the required clamping force across the joint. Less than 100% Tensioning Not all applications allow for the simultaneous fit of a tensioning device on each bolt, in these cases at least two tensioning pressures are applied. This is to account for a load loss in those bolts already tensioned as the next sets are tightened. The load losses are accounted for in calculation and a higher load is applied to allow the first sets to relax back to the target preload. Set-up Using a 50% Tensioning Procedure Half the bolts are tensioned simultaneously, the tools are relocated on the remaining bolts and they are subsequently tensioned. Read Instruction Manuals Please refer to the product Instruction Sheets for safe use guidelines and detail on the correct set up and operation of the equipment. 125
136 Strony | Ważny do 12/2023 | Previous page | Następna strona
Wybierz swój język
Zagadnienia prawne
Producent ponosi wyłączną odpowiedzialność za treść, cenę i szczegóły dotyczące produktów i ofert prezentowanych w katalogach. Z zastrzeżeniem zmian technicznych i optycznych przez producenta oraz błędów.
Formularz zapytania o produkty specjalne
Usługa zaopatrzenia ToolTeam®
Szukasz produktów, które znajdują się w katalogu, ale nie można ich kupić bezpośrednio online?Nasz dział zaopatrzenia z przyjemnością przedstawi Ci niezobowiązującą, indywidualną ofertę.
