Pneumax - Hauptkatalog Pagina 842
Commercieel klantenaanbod**Beste verkopers van Pneumax GmbH
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
Cylinders according to standard ISO 15552 Series 1386 - 1387 - 1388 - 1396 - 1397 - 1398 - ECOPLUS Series 1386-1387-1388/ 1396/1397/1398, ECOPLUS General Profiled tube has two "T" slots on the three sides hosting sensors 1580._, MRS._, MHS._. without adaptors. Construction characteristics End caps Series 1386 - 1388: Series 1396 - 1398: high resistant Die-casting aluminium thermoplastic material Rod C43 chromed steel or stainless steel Barrel anodised aluminium alloy Rod-guide bushing self-lubricating sintered bronze Piston acetal resin, aluminium on request Seal standard: NBR Oil resistant rubber, PUR Piston rod seals (PUR seals available upon request) Cushion adjusting screws 3 brass Pneumatic actuatiOn Operational characteristics Fluid Filtered air. No lubrication needed, if applied it shall be continuous. Max. pressure 10 bar Operating temperature -5°C - +70°C with standard seals -30°C - +80°C with PUR seals Bore Ø 32 - 40 - 50 - 63 - 80 - 100 Cushioning lenght mm 27 - 31 - 31 - 37 - 40 - 44 Cushioning lenght "K" and "PK" version mm 20 - 20 - 22 - 22 - 32 - 32 Please follow the suggestions below to ensure a long life for these cylinders: •use clean and lubricated air •correct alignment during assembly with regard to the applied load so as to avoid radial components or bending the rod; •avoid high speeds together with long strokes and heavy loads: this would produce kinetic energy which the cylinder cannot absorb, especially if used as a limit stop (in this case use mechanical stop device and aluminium piston); •evaluate the environmental characteristics of cylinder used (high temperature, hard atmosphere, dust, humidity etc.) Please note: air must be dried for applications with lower temperature. Use hydraulic oils H class (ISO VG32) for correct continued lubrication. Our Technical Department will be glad to help. Standard strokes (for all diameters) from 0 to 150, every 25 mm from 150 to 500, every 50 mm Stroke tolerance (ISO 15552) Bore Stroke up to 500 32 - 40 - 50 over 500 up to 1000 from 500 to 1000, every 100 On request are available strokes up to 2800 mm up to 500 63 - 80 - 100 over 500 up to 1000 3 | 46 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice Tolerance +2 0 +3.2 0 +2.5 0 +4 0
1106 Pagina’s | Geldig tot 06/2025 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.