Mahr - Product Catalog Pagina 308
Commercieel klantenaanbod**Producten uit de cataloguspagina
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
Millimar DP50 / DP20 2-Jet Blind Hole Air Plug HCC FEATURES • Calibrated ID tooling for the Dimensionair® Air Gaging Systems • Tooling is interchangeable without adjusting system magnification. • Federal Air Plugs have large clearance (see table below), allowing easy entrance into the hole being measured and a greater measuring range. • Long life - wide clearance and hard chrome (optional) body extends life of the Air Plug. • Deep, recessed jets - Air jets are recessed into the plug body, protecting them from damage. • Large jet size eliminates clogging from dirt and oils. • Order information: Please always state when ordering: Transmission ratio of the display unit (e.g. 2500:1), the nominal size to be measured and the specified workpiece tolerance Application: Measurement of blind holes Super-blind Plugs Blind Hole Air Plugs can be furnished to check shorter holes than listed above, and can be furnished to check closer to the bottom of a hole. Holes must be at least 2.79 mm/.110" long, and the distance from the end of the plug to the center-line of the jets can be as short as 2.16 mm/.075" for plugs below 6.34 mm/.250" or 2.16 mm/.095" for plugs above 6.34 mm/.250". TECHNICAL DATA Order no. Type Nominal value Model mm Nominal size in inches inch 2092961 DP50 2092962 Compatibility Clearance 3.937 – 4.696 .1550 – .1849” hardened steel 2500:1 38 Federal 0.027 DP50 4.699 – 6.312 .1850 – .2485” hardened steel 6.35 2500:1 51 Federal 0.03 2092963 DP50 6.314 – 9.484 .2486 – .3734” 6.35 hardened steel 2500:1 76 Federal 0.045 2092964 DP50 9.487 – 11.859 6.35 .3735 – .4669” hardened steel 2500:1 76 Federal 0.045 2092965 DP50 6.35 11.862 – 14.933 .4670 – .5879” hardened steel 2500:1 76 Federal 0.045 2092966 6.35 DP50 14.935 – 20.978 .5880 – .8259” hardened steel 2500:1 76 Federal 0.045 6.35 2092967 DP50 20.980 – 28.699 .08260 – 1.1299” hardened steel 2500:1 76 Federal 0.045 6.35 2092968 DP50 28.702 – 37.691 1.1300 – 1.4839” hardened steel 2500:1 76 Federal 0.045 6.35 2092969 DP50 37.694 – 44.193 1.4840 – 1.7399” hardened steel 2500:1 76 Federal 0.045 6.35 2092970 DP50 44.196 – 63.751 1.7400 – 2.5099” hardened steel 2500:1 76 Federal 0.045 6.35 2092971 DP50 63.754 – 76.299 2.5100 – 3.0039” hardened steel 2500:1 76 Federal 0.045 6.35 2092972 DP50 76.302 – 89.151 3.0040 – 3.5099” hardened steel 2500:1 76 Federal 0.071 6.35 • 2092973 DP50 89.154 – 101.851 3.5100 – 4.0099” hardened steel 2500:1 76 Federal 0.071 6.35 • 2092974 DP50 101.854 – 114.300 4.0100 – 4.5000” hardened steel 2500:1 76 Federal 0.071 6.35 • 2092991 DP20 3.937 – 4.696 .1550 – .1849” hardened steel 5000:1 19 Federal 0.013 6.35 2092992 DP20 4.699 – 6.312 .1850 – .2485” hardened steel 5000:1 25 Federal 0.015 6.35 2092993 DP20 6.314 – 9.484 .2486 – .3734” hardened steel 5000:1 38 Federal 0.023 6.35 2092994 DP20 9.487 – 11.859 .3735 – .4669” hardened steel 5000:1 38 Federal 0.023 6.35 2092995 DP20 11.862 – 14.933 .4670 – .5879” hardened steel 5000:1 38 Federal 0.023 6.35 2092996 DP20 14.935 – 20.978 .5880 – .8259” hardened steel 5000:1 38 Federal 0.023 6.35 2092997 DP20 20.980 – 28.699 .08260 – 1.1299” hardened steel 5000:1 38 Federal 0.023 6.35 2092998 DP20 28.702 – 37.691 1.1300 – 1.4839” hardened steel 5000:1 38 Federal 0.023 6.35 2092999 DP20 37.694 – 44.193 1.4840 – 1.7399” hardened steel 5000:1 38 Federal 0.023 6.35 2093000 DP20 44.196 – 63.751 1.7400 – 2.5099” hardened steel 5000:1 38 Federal 0.023 6.35 2093001 DP20 63.754 – 76.299 2.5100 – 3.0039” hardened steel 5000:1 38 Federal 0.023 6.35 2093002 DP20 76.302 – 89.151 3.0040 – 3.5099” hardened steel 5000:1 38 Federal 0.071 6.35 • 2093003 DP20 89.154 – 101.851 3.5100 – 4.0099” hardened steel 5000:1 38 Federal 0.071 6.35 • 2093004 DP20 101.854 – 114.300 4.0100 – 4.5000” hardened steel 5000:1 38 Federal 0.071 6.35 • 304 Magnifi- Measuring cation span µm Millimar | Electrical Length Measuring Instruments mm Minimum Including bore length handle mm
708 Pagina’s | Geldig tot 12/2023 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.