ENERPAC - Bolting Tools Pagina 125
Commercieel klantenaanbod**Beste verkopers van ENERPAC
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
Torque Tightening Manufacturer’s rating of pressure and torque are maximum safe limits. Good practice encourages using only 80% of these ratings! Torque Procedure Select the Correct Wrench Choose your Enerpac torque wrench using the untightening rule of thumb: • When loosening a nut or bolt more torque is usually required than when tightening. • For general conditions it can take up to 2½ times the input torque to breakout. • Do not apply more than 75% of the maximum torque output of the tool when loosening nuts or bolts. When torquing it is common to tighten only one bolt at a time, this can result in Point Loading and Load Scatter. To avoid this, torque is applied in stages following a prescribed pattern: Torque Sequence 1 1 1 5 12 5 8 9 8 4 3 3 4 4 3 10 6 2 7 7 2 Step 1: Spanner tight ensuring that 2-3 threads extend above nut Step 2: Tighten each bolt to one-third of the final required torque following the pattern as shown above. Step 3: Increase the torque to twothirds following the pattern shown above. 11 6 2 Step 4: Increase the torque to full torque following the pattern shown above. Step 5: Perform one final pass on each bolt working clockwise from bolt 1, at the full final torque. Conditions of Bolted Joints • Humidity corrosion (rust) requires up to twice the torque required for tightening. • Sea water and chemical corrosion requires up to 21⁄2 times the torque required for tightening. • Heat corrosion requires up to 3 times the torque required for tightening. Minimum Output Torque • The recommended minimum torque value of a hydraulic wrench is 10% of the maximum rated value. Breakout Torque Bolting Integrity Software A comprehensive on-line software solution for Bolted Joint Integrity. Integral databases hold data for: When loosening bolts a torque value higher than the tightening torque is normally required. This is mainly due to corrosion and deformations in the bolt and nut threads. • ASME B16.5, ASME B16.47, API 6A and API 17D flanged joints • Common gasket materials and configurations • Comprehensive range of bolt materials • Comprehensive range of lubricants • Enerpac's Controlled Bolting Equipment including: Torque Multipliers, Hydraulic Wrenches and Bolt Tensioning tools Custom Joint information can also be entered. Breakout torque cannot be accurately calculated, however, depending on conditions it can take up to 2½ times the input torque to breakout. The use of penetrating oils or anti-seize products is always recommended when performing breakout operations. The software offers Tool selection, Bolt Load calculations and Tool pressure settings, as well as, a combined Application data sheet and Joint completion report. 123
136 Pagina’s | Geldig tot 12/2023 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.