AMF Catalogue Hydraulic clamping systems Pagina 230
Commercieel klantenaanbod**Beste verkopers van AMF Spannsysteme
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
support element No. 6964HS-XX-1 Support element, threaded design with dynamic pressure monitoring 567072 Normally retracted. Hydraulic advanced. Application with spring force, max. operating pressure 350 bar, min. operating pressure 50 bar. Contact force F1 Support force at Stroke C Q max. Vol. Md max. Weight 350 bar [kN] [mm] [l/min] [cm³] [Nm] [g] [N] Article no. Order no. 567073 567074 567075 6964HS-09-1 6964HS-09-10 6964HS-18-1 6964HS-18-10 4,4 - 26,7 8,9 6,5 2,13 0,8 50 4,4 - 26,7 8,9 12,5 2,13 1,1 50 150 157 13,5 - 44,5 17,8 6,5 2,13 3,3 70 290 13,5 - 44,5 17,8 12,5 2,13 3,7 70 327 Design: Cylinder body from steel, hardened. Support pin with internal thread case hardened and ground. Wiper to protect against dirt and cooling water. Internal parts from stainless steel. Oil supply via oil channel in fixture body. Application: The support element is used as an extra support to prevent sagging and vibration of a workpiece. Also confirms the presence of a workpiece, also on uneven surfaces such as castings. Features: The piston is retracted into its basic position while an air flow passes through the support element. When pressure is applied, the support pin advances with a weak spring-applied force against the inserted workpiece. This closes the integrated air valve to indicate that the workpiece is present and is in contact. The maximum air operating pressure is 1 bar. Then the support pin is clamped hydraulically. When the pressure is released, the support pin returns to the normal position. Very high repeatability ensures optimum production quality. Element with high load capacity and low height. Note: Support pin must be protected against the entry of dirt and splash water by fitting a set screw or plug. When placing into operation, ensure that all air is bled from the system. Failure to do so can cause destruction of the clamping element by the escaping diesel effect. To be able to absorb machining forces, the supporting force should be matched to the clamping force. The supporting force should always be at least twice as high as the clamping force. Installation dimensions: Article no. G H K N dia. P ØR dia. S dia. T U 6964HS-09-1 M26 x 1,5 13,5 3,2 4,3 24,5 27 5 2 9,8 M26 x 1,5 13,5 3,2 4,3 24,5 27 5 2 9,8 M35 x 1,5 21,5 4,7 6,6 33,5 36 5 3 12,0 M35 x 1,5 21,5 4,7 6,6 33,5 36 5 3 12,0 Order no. 567072 567073 567074 567075 6964HS-09-10 6964HS-18-1 6964HS-18-10 Diagram: Supporting force (kN) 6964HS-18 max. Ø S on or inside radius K oil connection bore 6964HS-09 max. Ø T on or inside radius U air connection hole Pmax. 1 bar Operating pressure (bar) CAD Dimensions: Order no. 567072 567073 567074 567075 Article no. 6964HS-09-1 dia. A B D E F G J x depth L dia. M SW SW1 OR-1 O-ring Order No. OR-2 O-ring Order No. 14,3 57,8 43,7 6,3 5,5 M26 x 1,5 M8 x 5 7,1 23,3 23 11 567117 567114 6964HS-09-10 14,3 70,6 55,4 6,3 5,5 M26 x 1,5 M10 x 5 7,1 23,3 23 11 567117 567114 19,0 77,2 58,1 8,5 9,3 M35 x 1,5 M12 x 6,5 9,5 29,7 30 17 567118 567115 6964HS-18-10 19,0 89,7 67,9 8,5 9,3 M35 x 1,5 M12 x 6,5 9,5 29,7 30 17 567118 567115 6964HS-18-1 Subject to technical alterations. 230 Hydraulic clamping systems ANDREAS MAIER GmbH & Co. kg ∙ Phone: +49 711 5766-196 ∙ Web: www.amf.de
384 Pagina’s | Geldig tot 12/2025 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.
