AMF Catalogue Hydraulic clamping systems Pagina 10
Commercieel klantenaanbod**Beste verkopers van AMF Spannsysteme
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
screw pump No. 6901 Article no. max. operating pressure [bar] stroke volume per rev. [cm³] stroke volume total [cm³] Md max. [Nm] [g] 67819 6901-10 350 2,1 26 50 1524 67835 6901-20 350 2,1 26 50 689 Order no. Screw Pump block version and built-in version, max. operating pressure 350 bar. Weight Design: Housing from steel, hardened and burnished. Threaded spindle hardened and burnished. Screw pump no. 6901-20 is supplied with 2 grooved nuts. Oil supply via threaded port. Application: The screw pump is particularily suitable to operate small clamping fixtures. Note: 6901-10 For an enclosed circuit the following has to be considered: The hydraulic clamping elements connected to the screw pump have to be hermetically tight. Due to possible leakage of the clamping cylinders during stroke movement and the compressibility of oil (1% at 140 bar), the stroke volume of the screw pump shall be used up to 70% only. The compressibility is being increased considerabely by air content in the oil. Therefore the hydraulic system has to be carefully purged of air. An air bleed screw at the highest position is a necessity. After returing the spindle of the pump, oil must be refilled at this spot. No air pocket should arise in the hydraulic system, which cannot be purged. A precise pressure control is possible by a manometer only. An electric pressure switch enables a pressure monitoring too. A pressure limiting valve is not suitable. Operating the threaded spindle by a torque wrench is possible. However the pressure should also be checked by a gauge. For the built-in version the mounting torque has to be observed. 6901-20 6901-10 stroke Clamping pressure in relation to torque: Torque [Nm] Clamping pressure [bar] 13,5 27,0 34,0 40,5 47,5 70 140 205 275 350 oil connection 6901-20 threaded plug stroke CAD Subject to technical alterations. 10 Hydraulic clamping systems ANDREAS MAIER GmbH & Co. kg ∙ Phone: +49 711 5766-196 ∙ Web: www.amf.de
384 Pagina’s | Geldig tot 12/2025 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.
