AMF Catalogue ZERO-POINT SYSTEMS Pagina 155
Commercieel klantenaanbod**Beste verkopers van AMF Spannsysteme
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
excl. verzending
indexing t-nut No. 6370ZI Indexing T-nut For clamping modules with indexing. Case-hardened, burnished and ground, incl. fastening bolt. Size B H L 430264 10.2 / 10.3 / 20 8 8 10 6 550288 20.3 10 8 20 15 Order no. Weight [g] Application: Indexing T-nut is used for the precise positioning of workpieces or fixtures on a clamping module with indexing function. Note: Order no. 430264 incl. M3 fastening bolt. Order no. 550288 incl. M4 fastening bolt. CAD No. 6984-30 Support control, pneumatic Order no. 325217 Article no. Stroke max. Input pressure [mm] [bar] 5 1-2 6984-30 Spring force min. Spring force max. Weight [N] [N] [g] 1,9 2,6 36 Design: Housing from hardened and burnished steel. Pistons are tempered, nitrided and ground. Compression spring from stainless steel. Application: The support control is used in fixtures where a signal indicating a correctly supported workpiece is required to enable machining. Lightweight workpieces should be clamped before being pressurised with compressed air. Features: The support control works like a pneumatic back-pressure nozzle. The position is extended from its initial position by a pressure spring. Once applied, the air jet flows through the hollow piston and the radial discharge hole on the support control housing to outside. The discharge hole is sealed as soon as a workpiece is mounted and the piston is pushed downwards by min. 1 mm. The air flow backs up, the internal air pressure rises. The pressure value must be transferred to the control by an appropriate pressure signal converter. The system is relatively insensitive to fine chips. Switching stroke min. 1 mm stroke Note: The pressure signal converter is not included in the supply scope. Effective piston surface with closed nozzle = 0.95 cm² Piston force = piston surface x air pressure + spring force Reduce the input pressure to 1 bar up to a maximum of 2 bar when the air duct is open, e.g. with a throttle check valve. When the air duct is closed, there is a dynamic pressure of approx. 3 bar. Installation drawing pressure signal connection air connection CAD Subject to technical alterations. ANDREAS MAIER GmbH & Co. kg ∙ Phone: +49 711 5766-196 ∙ Web: www.amf.de ZERO-POINT-SYSTEMS 155
228 Pagina’s | Geldig tot 12/2025 | Vorige pagina | Volgende pagina
Kies uw taal
Juridische kwesties
De fabrikant is exclusief verantwoordelijk voor de inhoud, prijs en artikeldetails van de producten en aanbiedingen in de catalogi. Technische en optische wijzigingen door de fabrikant en fouten voorbehouden.
Aanvraagformulier voor speciale producten
De ToolTeam® Inkoopservice
Bent u op zoek naar producten die wel in de catalogus staan maar niet direct online te koop zijn?Onze aankoopdienst zal u graag een niet-bindend en individueel aanbod doen.
