Dynabrade - Industrial Katalog Pagina 158
Offerta per clienti commerciali**Prodotti della pagina del catalogo
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
“Swirl-Free Checklist” For Dynabrade Random Orbital Sanders Equipment Check: Sanding Techniques (Continued) q Random Orbital Sander q 90 PSIG (6.2 Bar) is the required operating air supply pressure. Check the air pressure at the sander while it is running. Note: Promote the use of Dynabrade maximum flow plugs and couplers to ensure proper airflow. q Confirm that the tool is running at the rated “Free Speed” RPM. On an average a 10,000 RPM non-vacuum sander will run at 9,500 RPM; a 12,000 RPM non-vacuum sander will run at 11,500 RPM. A vacuum sander normally runs slightly slower. q Inspect the balancer bearing (pad bearing). Remove the back-up pad and rotate the balancer bearing shaft while holding the counterbalance stationary. The balancer shaft should turn freely. Follow a set pattern when sanding. It is suggested to pass over the surface following a “North, South, East, West” pattern (see below), overlapping each pass 1/4 the diameter of the back-up pad and abrasive. This insures that the previous End scratches are removed and that a uniform finish is achieved. Two “patterns” per sanding step are recommended. Back-Up Pad q Start Inspect the face of the sanding pad. The pad must be flat and smooth, without any defects. Check if they are using a Dynabrade back-up pad that is “weight-mated” to the sander. Using another pad can make the sander vibrate excessively and lead to an unacceptable finish. q Frequently inspect abrasive for tears, folds, or build-up. When changing abrasive to proceed to the next sanding step, first inspect the condition of the abrasive that is on the sander. If any defects are noticed in that abrasive, remove it and install another piece of the same grain and sand the work surface again before proceeding on to the next sanding step. q Always clear away sanding dust and abrasive debris before progressing to the next sanding step with a finer “grit” abrasive. Sanding Techniques: q Always START the sander ON the surface, and STOP the sander OFF the surface. q When sanding keep the sander, and pad FLAT on the surface. Important: Do not exert heavy downward force on the sander. Apply enough downward force to keep the back-up pad and abrasive flat on the surface allowing the back-up pad to orbit freely over the surface. Two-Hand Dynorbital ® SANDING PADS PAGE 241 ACCESSORIES RANDOM ORBITAL SANDERS Air-Powered Random Orbital Sander PAGE 233 FOR ABRASIVE DISCS For Comfortable, Controlled Two-Hand Operation 5" (127 mm) diameter SEE PAGE 283 Model 57101 Low Profile Model • Unique low profile two-hand model is weight-mated to 5" diameter sanding pad. Model 57101 • 56106 Non-Vacuum, vinyl-face pad included. • Also includes convenient 97166 Hanger. • A versatile, lightweight two-hand random orbital sander. 3/16" (5 mm) Dia. Orbit For General Sanding Model Number Motor hp (W) Motor RPM Orbit Dia. Inch (mm) Pad Dia. Inch (mm) Sound Level Maximum Air Flow SCFM (L/Min) Hose I.D. Size Inch (mm) Air Inlet Thread Weight Pound (kg) Length Inch (mm) Height Inch (mm) 57101 .2 (149) 12,000 3/16 (5) 5 (127) 76 d(B)A 28 (793) 3/8 (10) 1/4" NPT 2.1 (.98) 8-5/16 (211) 3-3/4 (96) Tune-Up Kit: No. 96537 • Additional Specifications: Air Pressure 90 PSIG (6.2 Bar) 158
316 pagine | Valido fino a 07/2026 | Previous page | Pagina successiva
Selezionare la lingua
Questioni legali
Il produttore è esclusivamente responsabile del contenuto, del prezzo e dei dettagli degli articoli dei prodotti e delle offerte presentati nei cataloghi. Con riserva di modifiche tecniche e ottiche da parte del produttore e salvo errori.
Modulo di richiesta per prodotti speciali
Il servizio di acquisto di ToolTeam®
State cercando dei prodotti che sono mostrati nel catalogo ma che non possono essere acquistati direttamente online?Il nostro servizio di approvvigionamento sarà lieto di farvi un’offerta individuale e non vincolante.