CELO main catalog Pagina 103
Offerta per clienti commerciali**I migliori venditori da CELO Befestigungssysteme GmbH
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
escluse le spese di spedizione
CELO Monting in concrete L dk h e ef = 3x 1. Drill a hole: Drill hole depth + insulation $WWDFKWKHPL[LQJQR]]OHH[WHQVLRQ0'9WRWKH 3. Cut the ResiTHERM® 16 or 12 to length: thickness After determining the correct length, cut the threaded rod to length with a metal saw or similar. PL[LQJQR]]OH0' Squeeze out the injection mortar until the mortar has DXQLIRUPJUH\PL[LQJFRORXUGLVFDUGWKH pre-run of the first at least 3 strokes. VY 300SF 6 5 4 °C Resi 2. Clean the drill hole properly according to ETA: [EORZ[EUXVK[EORZ 5. Fill at least 2/3 of the drill hole with composite mortar (start from the beginning). For number of 6. Screw in the ResiTHERM®RUZLWKWKHKH[DJRQ 7. Observe curing time of the injection system, see bit (included) and a cordless screwdriver until the seal cartridge label of the ResiFIX injection mortar. strockes see mounting instructions at www.celofixings.com. Important: Follow the installation instructions and is pressed against the plaster. Note: The thermal separation module drills itself through the insulation (additional sealing is not processing time of the ResiFIX injection mortar used in accordance with the approval/assessment. necessary, unless the plaster is very rough) 8. Afterwards, the attachment can be mounted, PD[WRUTXH7inst = 25 Nm (ResiTHERM® 16) or 19 Nm (ResiTHERM® 12) Mounting in masonry (hollow brick) Ldk 125 mm 1. Drill a hole: Drill hole diameter = 20 mm. e 4. Enlarge the opening in the plaster for the collar of the 3. Cut the ResiTHERM® 16 or 12 to length: 'ULOOKROHGHSWK͡PPLQVXODWLRQWKLFNQHVV LQFO Correct length LdK: Anchorage depth in plastic sleeve (125 mm) + insulation thickness e (incl. plaster) plaster). Observe the drilling procedure of the approval/ assessment of ResiFIX injection mortar. Perforated bricks and aerated concrete: Rotary After determining the correct length, cut the threaded rod to length with a metal saw or similar. plastic sleeve to 26 mm. To do this, briefly screw the thermal separation module in and out through the SODVWHUIRURQO\DSSUR[WKUHDGWXUQVRUUHDPWKH plaster with a drill or drill with a bigger 26 mm drill. 5. Push the plastic sleeve into the drill hole with the help of a folding ruler or similar. VY 300SF 6 4 5 Resi drilling - without impact 2. Clean the drill hole properly according to ETA: [EORZ[EUXVK[EORZ = 3x $WWDFKWKHPL[LQJQR]]OHH[WHQVLRQ0'9WRWKH 7. Fill the plastic sleeve completely with composite PL[LQJQR]]OH0' Squeeze out the injection mortar until the mortar has mortar (start from the beginning). For number of strockes see mounting instructions at DXQLIRUPJUH\PL[LQJFRORXUGLVFDUGWKH pre-run of the first at least 3 strokes. www.celofixings.com Important: Follow the installation instructions and processing time of the ResiFIX injection mortar used in accordance with the approval/assessment. 8. Screw in the ResiTHERM®RUZLWKWKHKH[DJRQ bit (included) and a cordless screwdriver until the seal is pressed against the plaster. Note: The thermal separation module drills itself 102 through the insulation (additional sealing is not necessary, unless the plaster is very rough) 9. Observe curing time of the injection system, see cartridge label of the ResiFIX injection mortar. 10. Afterwards, the attachment can be mounted, PD[WRUTXH7inst = 25 Nm (ResiTHERM® 16) or 19 Nm (ResiTHERM® 12)
316 pagine | Valido fino a 03/2023 | Previous page | Pagina successiva
Selezionare la lingua
Questioni legali
Il produttore è esclusivamente responsabile del contenuto, del prezzo e dei dettagli degli articoli dei prodotti e delle offerte presentati nei cataloghi. Con riserva di modifiche tecniche e ottiche da parte del produttore e salvo errori.
Modulo di richiesta per prodotti speciali
Il servizio di acquisto di ToolTeam®
State cercando dei prodotti che sono mostrati nel catalogo ma che non possono essere acquistati direttamente online?Il nostro servizio di approvvigionamento sarà lieto di farvi un’offerta individuale e non vincolante.