ZARGES Main Catalog packaging and transportation Page 224
Offre client commercial**Produits de la page du catalogue
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
SHAFT COVERS Made of aluminium. Shaft covers that can be stepped on or driven over, with customisable surface or cover plate, for both indoor and outdoor use. Recommendations for selection of shaft covers The choice of material depends on the application, load and environmental conditions. The shaft covers with trough can be filled with the same material (e.g. tiles, carpets or cobblestones) as the ground around it to help it blend in perfectly with its surroundings. The shaft covers with cover plate are the ideal solution for lower loads of up to 1.5 t. The cover plate is made of serrated, non-slip aluminium, steel chequer plate, hot-dip galvanised or V2A (1.4301), pickled and passivated. The frame is made from hot-dip galvanised steel or V2A (1.4301) stainless steel section. Flush installation EN 124 applies to covers of up to 1,000 mm (inside width) used in areas with pedestrian and/ or vehicle traffic. DIN 1229 specifies the minimum weights for covers. In compliance with EN 124 and DIN 1229 Indoor Exterior (Aluminium) If the shaft cover is supposed to blend in with the ground around it, you should select shaft covers with trough. (Steel) Trough Hygiene (Stainless steel) Cover plate Chequer or diamond plate ■ In compliance with EN 124 and DIN 1229. ■ Tapered profile-section construction with multiple bolted joints. ■ Easy to open, no jamming. ■ EPDM seal. ■ Odour-tight and impervious to surface water. ■ Load with choice of surface: Test force 125 kN (=12.5 t), only after cover trough has been filled by customer with concrete. ■ Load with cover plate: test force 15 kN (=1.5 t). ■ Incl. lift-out handles (pair) made from stainless steel, comprising one self-lifting opening handle and one liftout handle. Dimensions (inside dimensions) 06 80 mm 62.5 mm Aluminium Installation flush with the ground in acc. with EN 124 and DIN 1229 Aluminium recommended for indoor applications* Aluminium recommended for indoor applications* Aluminium, serrated recommended for indoor applications* Galvanised steel recommended for indoor applications* Type of cover with trough1) for choice of surface with cover plate2) Height, mm 80 62.5 Material, cover Material, frame 60 (40 covered with construction steel grating and 20 free area) Trough depth, mm Shaft inside dimensions, mm × mm Order no. Outside dimensions mm – Order no. Outside dimensions mm 300 × 300 47000 440 × 440 – – 450 × 450 47001 590 × 590 – – 500 × 500 47002 640 × 640 – – 600 × 600 47004 740 × 740 47021 760 × 760 635 × 635 47005 775 × 775 – – 800 × 800 47007 940 × 940 47023 960 × 960 1,000 × 1,000 47010 1,140 × 1,140 47024 1,160 × 1,160 *Recommendation; other materials can also be used if requested by the customer. 1) 2) Load class for attachment with B 45 concrete Class B 12.5 t. In the case of partial attachment, pedestrians only. Load class A 1.5 t. 224 Shaft and well covers, shaft equipment
340 Pages | Valable jusqu’au 12/2026 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.