WEICON Main Catalogue Chemical and technical products Page 59
Offre client commercial**Meilleures ventes de Weicon
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Polyurethane Systems PU-90 PU-240 Base - 0 5% Phosphoric acid + Petrol (92 to 100 octane) - Phosphoric acid (concentrated) - Diesel/heating oil - 2-Propanol - Glycol ether - 5% Nitric acid - > 5% Acetic acid - 5% Hydrochloric acid + Ethanol - Salt water/seawater + Freon - 5% Sulphuric acid o Antifreeze + Silicone oil (concentrated) - Gear oil - Edible oil/vegetable oil - Glycerine (glycol) + Toluene + Hydraulic oil 0 Naphtha + 20% Caustic potash solution + Water + Ketones - Water, +90°C o Cooling lubricant, water-dilutable + W3% Hydrogen peroxide + Thinner - Paraffin oil + Lyes, thinned + Xylene + Methanol - 10% Citric acid + + = resistant 0 = resistant for a limited time - = not resistant Easy-Mix PU-90 Easy-Mix PU-240 Easy-Mix PU Crsytal polyurethane polyurethane polyurethane Mixing ratio resin/hardener 1:1 1:1 1:1 Colour after curing black black crystal-clear 1.30 - 1.35 g/cm3 1.30 - 1.35 g/cm3 1.13 g/cm3 Pot life at +20 °C (+68 °F) 90 sec. 240 sec. 2 - 4 min. Handling strength (35 %) after 5 min. 10 min. 30 min. Mechanical loads (50 % strength) after 10 min. 30 min. 60 min. 12 h 12 h 12 h 0.1 - 4.0 mm 0.1 - 4.0 mm 0.1 - 4.0 mm Density of the mixture Final strength (100 %) after Adhesive gap bridging On Aluminium (0.26 mm) 13 N/mm2 (1,900 psi) 14 N/mm2 (2,000 psi) 11 N/mm2 (1,600 psi) On Steel bright (0.26 mm) 19 N/mm2 (2,800 psi) 23 N/mm2 (3,300 psi) 17 N/mm2 (2,500 psi) On Stainless steel (0.26 mm) Shore hardness D (DIN ISO 7619) 17 N/mm2 (2,500 psi) 650 - 750 N/mm2 (90 - 110 ksi) 66 18 N/mm2 (2,600 psi) 450 - 550 N/mm2 (70 - 80 ksi) 68 17 N/mm2 (2,500 psi) 240 - 280 N/mm2 (35 - 40 ksi) 73 Tensile strength DIN EN ISO 527-2 21 N/mm2 (3.000 psi) 20 N/mm2 (2.900 psi) 12 N/mm2 (1.750 psi) Thermoforming resistance 35 % -55 to +125°C (-67 to +257°F) +65°C (+149°F) 31 % -55 to +125°C (-67 to +257°F) +65°C (+149°F) 20 % -55 to +100°C (-67 to +212°F) +50°C (+122°F) TGA decomposition temperature (onset-temp.) Average E-module +20 °C (+68 °F) Tensile Extension DIN EN ISO 527-2 Temperature resistance Glass transition temperature Technical Sprays - 20% Sodium hydroxide solution 10% Ammonia Technical Liquids Formic acid (concentrated) +330°C (+626°F) +336°C (+637°F) - Tg after curing at room temperature +45.6°C +30.9°C +48.0°C Tg after tempering at +120 °C +31.1°C +27.0°C - Catalogue WEICON Assembly Pastes Technical Data + Lubricants a - 0 Mineral and synthetic motor oil WEICON TOOLS® pe onto uminium pi Gluing an al nel pa nt fro plastic PU-240 - Methyl ethyl ketone Alcohol Other of plastic Production nels pa h ic w sand 0 PU-9 Acetone Adhesives / Sealants Chemical resistance of WEICON Polyurethane Systems after curing 59
244 Pages | Valable jusqu’au 12/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.