TOX product catalogue Page 97
Offre client commercial**Meilleures ventes de TOX-DÜBEL
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Building materials & Holding values C 20/25 Vertically perforated brick Hlz 12 Perforated lime sand brick KSL 14 Hbn Lightweight concrete Hbn 2 Hbl Concrete Hbl 4 Solid lime sand brick KS 27 Brick Mz 20 500 kg * 100 kg 70 kg 60 kg 1 20 kg 1 170 kg 170 kg 70 mm 90 mm** 90 mm** 100 mm 90 mm** 100 mm 100 mm 70 mm 85 mm** 85 mm** 100 mm 85 mm** 100 mm 100 mm Drill Ø 14 mm (20 mm in plaster) 20 mm (25 mm in plaster) 20 mm (25 mm in plaster) 14 mm (20 mm in plaster) 20 mm (25 mm in plaster) 14 mm (20 mm in plaster) 14 mm (20 mm in plaster) Tightening torque 20 Nm 6 Nm 8 Nm 10 Nm 2 Nm 20 Nm 10 Nm Concrete Concrete uncracked cracked C 20/25 Holding values 3 (per fastening point without environmental effects) 500 kg * Drill hole depth h1 2 Anchoring depth hef Thermo Proof Shear loads as a function of the non-load-bearing layer (insulation & plaster) with full clamping α = 2 of a fastening point without environmental effects tETICS 62 mm 80 mm 100 mm 120 mm 140 mm 160 mm 180 mm 200 mm Shear loads 90 kg 81 kg 68 kg 58 kg 51 kg 46 kg 41 kg 38 kg The partial safety factors of the assessments and a partial safety factor γF = 1.4 of the impact are to be considered in the holding values Approved wall plugs must be used for fixings where safety is of importance (see also www.tox.de/safety+loads) 1 Not included in approvals Z-21.8-2011 2 Applies to the drill hole depth in the building material. The thickness of the insulation and plaster layer are still to be added Chemical / Heavy Duty 3 The entire approval notice Z-21.8-2011 and the approvals ETA-09/0258, ETA-13/0052 and ETA-13/0053 + ETA-13/0047, ETA-17/0501, ETA-17/0503 listed therein must be observed when sizing * Corresponds to the permissible bearing load of the ISO spacer ** with sieve sleeve Description & Area of Application Thermo Proof is a heavy-duty spaced mounting system for thermally-insulated facades (ETICS) consisting of: Iso Spacer with large contact surface and SW24 driver for better force transmission Aqua-Stop special sealant for exterior use; incl. dosing tip; content 80ml; transparent colour Steel parts made of stainless steel in A4 quality; M12 thread; length 300/400 mm Static mixer extension for deep drill holes Processing & Installation Drill through thermal insulation Measure thermal insulation 1. Drilling 6. Fill with injection mortar 2. Measure and shorten if necessary 7. Set threaded rod 3. Drill completely 8. Allow mortar to cure 4. Clean thoroughly 9. Seal with Aqua-Stop 5. Insert sieve sleeve 10. Fasten the attachment Drill a hole in the building material and remove the plaster layer if necessary Clean drill hole Shorten threaded rod if necessary (length = drill hole depth + insulation layer + attachment + 20 mm) and screw on Iso Spacer In perforated brick only with sieve sleeve. Insert this completely into the drill hole Fill 2/3 of the drill hole in the substrate or the sieve sleeve completely with injection mortar Insert the threaded rod with the pre-fitted Iso Spacer into the drill hole with a slight twisting motion Screw on the Iso Spacer until just before the plaster is applied Allow injection mortar to cure Seal gap with Aqua-Stop Mounting the fixture 97
216 Pages | Valable jusqu’au 12/2023 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.