STUBAI - Gesamtkatalog Page 305
Offre client commercial**Meilleures ventes de Stubai ZMV GmbH
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
BIEGE- UND SCHLIESSWERKZEUGE/ BENDING - AND CLOSINGTOOLS Nr. 2824 STUBAI Winkeldoppelfalzer N° 2824 STUBAI Double seamer Artikel Größe Nummer mm 2824 15 2824 15NR 2824 23 220 mm 220 mm Ersatzachse/ repl. bolt EAN-Nr. 9002793 2500 g 2500 g 33 g 1 1 2 843063 876825 861647 Ideal zum Schließen des geschlossenen Winkelfalzes (Fahnenfalz) zum doppelten Stehfalz in einem Arbeitsvorgang. Ideal for shaping of locked angleseam to doubleseam in one go. Nr. 2824 15 Nr. 2824 15NR Nr. 2824 STUBAI Traufenkanter N° 2824 STUBAI Drip edge bender Artikel Größe Nummer mm 2824 13 2824 13NR 2824 22 250 mm 250 mm Ersatzachse repl. bolt EAN-Nr. 9002793 1700 g 1700 g 84 g 1 1 2 815374 876849 861623 Ideal zum schnellen und sauberen Einfalzen des Bleches an der Traufe, Dachgauben, und Abtreppungen; ermöglicht Kantungen von über 90°; umgelegter Doppelstehfalz kann durch die breite Öffnung mit abgekantet werden, Einfalzen ohne Hammer, deshalb keine Hammerschläge auf dem Blech sichtbar. Nr. 2824 13 This tool makes a clean bend without leaving any marks. This tool will make a bend over 90°. Because of its wide opening. It is also possible to bend a flat-seamed standing seam around and under the drip edge. Nr. 2824 13NR Nr. 2824 STUBAI Traufenschließer N° 2824 STUBAI Drip edge seamer Artikel Größe Nummer mm 2824 14 2824 14NR 2824 23 200 mm 200 mm Ersatzachse repl. bolt EAN-Nr. 9002793 2276 g 2276 g 33 g 1 1 2 815404 876832 861647 Ideal zum Schließen der vorgefalzten Traufenkante, Fertigfalzen ohne Hammer, deshalb keine Hammerschläge auf dem Blech sichtbar, Fertigbiegen der Traufenkante in zwei Arbeitsgängen. Nr. 2824 14 This is the follow-up tool to the drip edge bender. It permits a clean and fast locking of the drip edge without any tool marks. Nr. 2824 14NR Seite 305 | page 305
412 Pages | Valable jusqu’au 12/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
