SKYLOTEC Wind Energy Flyer Page 14
Offre client commercial**Meilleures ventes de SKYLOTEC
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
HARNESSES IGNITE PROTON WIND Dieser voll ausgestattete Auffang-, Halte- und Steigschutzgurt mit KunststoffGleitplatte wurde speziell für die Windenergie entwickelt. IGNITE PROTON punktet mit einem thermogeformten Hüftpolster, welches die Last gleichmäßig auf der Hüfte verteilt und von außen mit einer schützenden Kunststoff-Platte gegen Abrieb geschützt ist. Die richtige Position der Auffangösen lässt sich dank der ausgeklügelten Konstruktion perfekt auf den Anwender anpassen. Überschüssiges Gurtband ist dank praktischer Gurtbandfixierung kein Störfaktor mehr. Schulterund Beinpolster sind bei Bedarf waschbar oder austauschbar. Vorgeformten Materialschlaufen und Werkzeugösen für verschiedenste Einsätze machen den Gurt zu einem Komplettsystem. • anwendbar mit allen Karabineröffnungsweiten ab 10,5 mm • thermogeformtes Hüftpolster • austauschbare Schulter- und Beinpolster This fully equipped fall arrest, holding and climbing harness with plastic glide plate was specially developed for wind energy. IGNITE PROTON scores with a thermoformed hip pad that distributes the load evenly on the hips and is protected against abrasion from the outside with a protective plastic plate. The correct position of the catching eyes can be perfectly adjusted to the user thanks to the ingenious design. Excess webbing is no longer a nuisance thanks to the practical webbing fixation. Shoulder and leg pads are washable or replaceable if necessary. Pre-formed gear loops and tool loops for a wide range of uses make the harness a complete system. • can be used with all karabiner opening widths from 10.5 mm • thermoformed hip pad • exchangeable shoulder and leg pads G-1132-WS EN 358:2018, EN 361:2002, ANSI/ASSP Z359.11-2021, MEETS CAN/CSA Z259.10-18, OSHA Polyester, Aluminium, Steel 140 kg 14
56 Pages | Valable jusqu’au 12/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
