Pneumax - Process Automation Page 39
Offre client commercial**Meilleures ventes de Pneumax GmbH
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Air service units Series 1700 Steel line Process automation technology Catalogue Filter regulators Filter-pressure regulator diaphragm with over-pressure drain (Relieving) Body, adjustment mechanism, back plate and caseback internal components in AISI 316L stainless steel Fixing screws, adjustment screw and locking nut in inox A4 (AISI 316) Clean profile versions available Filter cartridge available in AISI 316 stainless steel or HDPE Low hysteresis rolling diaphragm Balanced system Manual or automatic drain ATEX certification (II 2G or II 2D), SIL, EAC 1 2 1 Note The pressure must be always regulating while increasing. For a more precise regulation and higher sensibility, the use of a regulator with a pressure range as close as possible to the regulated pressure is recommended. 2 Size Technical characteristics Size 2 Size 3 Size 4 Rough finishing Clean profile (Bowl and adjustment mechanism) Type 1/4” NPT 3/8” NPT G1/4” IN / OUT connections 1/4” NPT 1/2” NPT G1/2” Assembly configuration 3/4” NPT 1” NPT G1” Stand alone Assembly position Vertical Filter pore size 5 µm 20 µm 50 µm 0-2 0-4 0-8 0-12 Pressure range (bar) Max. bowl capacity (cm3) 0-2 0-4 0-7 0-10 34 68 90 Manual Automatic Condensation drain Regulation Manual Pressure measurement 1/8” NPT pressure gauge connection port Size Operational characteristics Size 2 Size 3 Size 4 Size 2 Size 3 Size 4 Manual condensation drain Automatic condensation drain Maximum working pressure (bar) 20 (standard version) 16 (automatic drain version) 10 (reduced orifice automatic drain version) Minimum working pressure (bar) / 0,5 -30 ... +80 (standard version) -50 ... +80 (low temperature L version) -60 ... +80 (low temperature version -60 °C Z) -5 ... +150 (lhigh temperature H version) -40 ... +100 (EPDM-FDA version) -5 ... +70 (automatic drain S version and reduced orifice automatic drain SR version) Working temperature (C°) Size Weight Size 2 Size 3 Standard version (g) 1492 2557 6253 Automatic drain version / Reduced orifice automatic drain version (g) 1579 2723 6290 Overall dimensions and technical information are provided solely for informative purposes and may be modified without notice Size 4 37 PROCESS AUTOMATION TECHNOLOGY AISI 316 stainless steel adjustment springs
164 Pages | Valable jusqu’au 06/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
