Kukko puller guide Page 13
Offre client commercial**Meilleures ventes de Kukko
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
SEPARATING SEPARATING Mode of operation Selection of the right separating type The part to be removed is level. It is not possible to use standard puller jaws! pull For pulling tight parts such as ball bearings, roller bearings, inner rings and simliar. The sharp, wedge-shaped blades are pressed behind the parts to be removed and, in this process, push between the bearing and the seat. For pulling, the tension bolts on the pulling device (series 18) must be screwed into the separator. pull pressure 1st step: What is the diameter of the flush bearing? Normally, a separator blade is used in combination with a puller device. ? mm If the separating jaws are screwed into the pulling device the other way round, then pulling can be carried out flush and gently. Accessories: Extansions In some cases, an appropriate puller from the 20 series can be used instead of the puller bar. Accessories: long hydraulic spindles 2nd step: Choice of the separator blade 2 Seporator series 15 Separator with quick clamping pressure spindle, series 17 8-155 mm 6-250 mm TIP: One-hand operation due to quick-tension spindle It is also possible to extend the puller bar for jobs involving longer shafts. For particularly secure parts, in the larger models (from 18-2), the mechanical pressure spindle can be swapped for a hydraulic pressure spindle. More Separators 3rd step: Choice of the pulling device SEPARATING 3 pulling device series 18 SEPARATING 2 The extensive KUKKO line also supplies separators with side clamps, such as the 204 and 210 Cobra series. 50-440 mm Safety instructions for separating 4th step: Combination of the separating blade with the pulling device 4 Separator series 15 + series 18 24 4 Separator with quick clamping pressure spindle series 17 + series 18 www.KUKKO.com The adjusting nuts on the separator must be tightened in alternating and equal turns. Otherwise, the separator blade may tilt on the bolt or the thread may be damaged. www.KUKKO.com When pulling the separator blade, ensure that before the pulling device is pulled upwards the blade is firmly seated up to the stop under the part to be removed. The side bolts of the pulling device must always be spindleed into the separator blade until they stop. 25
17 Pages | Valable jusqu’au 12/2020 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
