GENIUS Main catalog Hand tools Page 490
Offre client commercial**Meilleures ventes de GENIUS Tools
Automotive Tools AT-08 10 Piece Disc Brake Caliper Tool Set Item No. 008ATS 008ATA 008ATF 008ATP 008AT0 008AT2 008AT4 008AT6 008AT7 008AT8 Blow Case 2100 g Description Pusher Screw Handle (R) 3/8" Square Dr. Adapter (2 Pins ø = 6mm ) 55mm(2-3/16") Adapter 54mm(2-1/8") Adapter (1 Pin ø = 5.5mm ) 63mm(2-1/2") Adapter (1 Pin ø = 5.5mm ) 51mm(2") Adapter (1 Long & 2 Short Pins ø = 6mm ) 32mm(1-1/4") Adapter (2 Short Pins ø = 5mm ) 42mm(1-5/8") Adapter (2 Long Pins ø = 6mm ) 42mm(1-5/8") Adapter (2 Short Pins ø = 6mm ) 47mm(1-7/8") Adapter (1 Pin ø = 5.5mm ) 10 sets / 22 Kgs / 2.2 CUFT • Jack up the car and support on axle stands, Then remove the relevant road wheel. • Remove the caliper from its carrier and take out the brake pads. • Fit the main body of the wind back tool into the caliper, turn the main thrust bolt clockwise to compensate for the distance between the position and caliper body. • Select the correct adapter and fit it to the end of the main thrust bolt, contiune rotating into the mating recesses in the piston. • Turn the thrust bolt to wild the calper piston back into its housing • Fit the new break pads and bolt the caliper back into the carrier AT-09 9 Piece Valve Spring Compressor Set Item No. 009009 009016 009019 009023 009025 009030 009070 009110 Blow Case 2000 g Description 250mm(10") "C" Clamp 16mm Driving Adapter 19mm Driving Adapter 23mm Driving Adapter 25mm Driving Adapter 30mm Driving Adapter 70mm Length Pressure Screw 110mm Length Pressure Screw 4 sets / 9 Kgs / 1 CUFT • These tools are designed to compress and release valve springs. • After removal of collects, pantograph-type levers ensure a consistent coaxial contact with the valve. • They work efficiently on all automobiles, trucks and tractor motors. AT-4808 8 Piece Inner Tie Rod Tool Set Item No. 048014 048017 048033 048038 048040 048042 048046 048080 Blow Case 2400 g Description 14mm Open Jaw Driver 17mm Open Jaw Driver 33.6mm Open Jaw Driver 1-3/16" Open Jaw Driver 1-1/4" Open Jaw Driver 1-5/16" Open Jaw Driver 1-7/16" Open Jaw Driver Long Socket 6 sets / 15.5 Kgs / 1.35 CUFT • These tools are specially designed for the inner tie rods that are inaccessible to adjust. • The inner tie rod can be easily removed and installed by slipping the long socket over the tie rod end and connecting it to the open-jaw driver. PROFESSIONAL TOOLS J-3
614 Pages | Valable jusqu’au 12/2023 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.