GEDORE Automotive KLANN Car Specialty Tools Catalogue Page 4
Offre client commercial**Produits de la page du catalogue
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
1. Springs and Shock Absorbers KL-0029-100 EB (Code 3294668) (Patented) KL-0029-100 EB Coil Spring Pre-Compressor, in a Foam Insert The base coil spring pre-compressor allows you to remove and install MacPherson struts in a particularly time-saving manner. For this, it is used in conjunction with the corresponding vehicle-specific upgrade kit (cf. accessory). A decisive advantage of this pre-compressor is the fact that by pre-compressing the MacPherson strut in situ on the vehicle, the strut can be removed without the need for releasing the control arm/drive shaft, upper ball joint and track rod joint. As a result, wheel alignments that might be required by the vehicle manufacturer are no longer necessary. The well-thought-out design of the tool in conjunction with the vehicle-specific upgrade kits (available separately) allow for a wide range of applications - irrespective of the shape of the springs. Substantial time savings of up to 25%, among other benefits, make this spring precompressor a rewarding investment for many years to come. Required Accessory: Vehicle-specific upgrade kits KL-0029-1.. Recommended Accessory: KL-0104-21-1 B Spreader Tool (adjustable), with Wedge No.1 + 2, KL-0104-21.. Accessories (cf. scope of delivery of KL-0104-21 KB) Tool Storage System: KL-0029-2090 - Plastic Storage Case Advantages: • Substantial time and cost savings. • Eliminates the need for releasing the control arm. • Eliminates the need for releasing the drive shaft. • Eliminates the need for releasing the track rod end or upper ball joint. • Eliminates the need for wheel alignment. • Design allows for use on coil springs regardless of their shape and pitch. • All components are available individually as spare parts. Note / Accessory: The coil spring pre-compressor must never be used for the disassembling of suspension struts. To remove stuck/tight-fitting shock absorbers/strut units from stub axle clamping bores, it is essential to enlarge the clamping bore with the aid of the KL-0104-21-1 B spreader tool. KL-0029-100 A Coil Spring Pre-Compressor Like the KL-0029-100 EB, however, supplied without Foam Insert. Technical Data: Maximum load capacity: Maximum span*: Compression travel*: Clamping nut drive: 17,500N 345mm 120mm 27mm Scope of Delivery: KL-0029-100 EB Coil Spring Pre-Compressor, in a Foam Insert Part No. Description KL-0029-100 A Coil Spring Pre-Compressor (Basic Unit) KL-0029-1090-1 A Foam Insert Qty 1 1 * = without support plate 4 Copyright GEDORE Automotive GmbH, Germany, 10.E1 formerly
220 Pages | Valable jusqu’au 12/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.