Ganter Norm Standard Parts - Catalogue Page 1648
Offre client commercial**Meilleures ventes de Ganter Norm
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Universal Joints with Friction Bearing Extract Stainless Steel, Single or Double 2 Bore code B Without keyway K With keyway V With square 1 d1 3 4 4 l1 l2 Type EG Type DG 34 Bore s H10 Square 6 V 6* 16 8 V 8* 22 10 V 10 * 25 12 V 12* 56 86 32 16 V 16* 68 105 42 20 V 20 * 82 128 50 25 V 25* 108 163 16 d 2 H7 3 l3 l4 t +1 Max. assembly length of the shaft 56 17 22 8 40 62 20 22 11 48 74 24 26 12 28 30 13 34 37 16 41 46 18 54 55 26 3.5 EG Single, friction bearing DG Double, friction bearing 3.4 Type 3.6 5 3.3 3.2 3.1 DIN 808 * not available from stock, requires a minimum order quantity Stainless steel AISI 304 • Keyway JS9 DIN 6885 Page 2078 • Cross Holes GN 110.1 Page 2081 • ISO Fundamental Tolerances Page 2151 • Stainless Steel Characteristics Page 2166 • RoHS On request • With other or unequal bores NI Since the moveable parts are not surface treated, i.e. not case hardened, the possibilities of application of these universal joints are much more limited compared to the ones made of standard steel. Therefore, the guide lines for the selection of universal joints with friction bearing Page 1644 according to the diagram may be applied at a limited extent only. Rotational speeds over 200 min may become critical. For continuous use of the stainless steel universal joints, ample lubrication is very important. This achieved by fitting the joint with a grease filled gaiter GN 808.1 Page 1653. 3.7 • Information 3.8 6 The order example refers to universal joints with equal bores both ends d2 or s. 3.9 Specification How to order 1 2 3 4 5 6 DIN 808-32-B16-105-DG-NI 1 d1 2 Bore code 3 d 2 (s) 4 l 2 (l1) 5 Type 6 Material 3.6 Moving, Transferring, Connecting with Shafts and Joints | Page 1647
2210 Pages | Valable jusqu’au 12/2026 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
