ENERPAC - ПРОМЫШЛЕННЫЕ ИНСТРУМЕНТЫ Page 180
Offre client commercial**Meilleures ventes de ENERPAC
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Компактный гидравлический перфоратор ▼ На фото: SP35S Намного быстрее, чем сверление Набор инструментов Входит в комплект 35-тонных перфораторов для установки пуансонов в штамп.Может быть заказан вместо номера модели SPK10. Информация по заказу 35-тонный перфоратор может быть заказан как отдельно, так и составе набора, включающего насос.Пуансоны и матрицы можно заказать отдельно, а также в виде комплекта. См. таблицу быстрого выбор на следующей странице. • Пробивает мягкую сталь толщиной до 12,7мм • Круглые, прямоугольные и квадратные отверстия • Надежная конструкция с цилиндром одностороннего действия и возвратной пружиной • Прочный металлический ящик для хранения пуансонов и матрицы вместе с перфоратором • В комплект входит соединение CR400 ▼ Схема выбора стандартных пуансонов и матриц Форма отверстия Дюймовый 1) (дюймы) Размер отверстия Метрический 1) (мм) Размер болтов Размер отверстия Размер болтов 1/4 7,9 9,5 11,1 13,5 14,3 17,5 19,8 20,6 7,9 9,5 11,1 12,7 7,9 x 19 9,5 x 19 11,1 x 19 12,7 x 19 – M8 M10 M12 – M16 M18 – – M8 M10 M12 – M8 M10 M12 ▼ SP35 Кkомпактный гидравлический перфоратор – Намного быстрее, чем сверление. 0,31 0,38 0,44 0,53 0,56 0,69 0,78 0,81 0,31 0,38 0,44 0,50 .31 x .75 .38 x .75 .44 x .75 .50 x .75 1) 178 5/16 3/8 7/16 1/2 5/8 – 3/4 1/4 5/16 3/8 7/16 1/4 5/16 3/8 7/16 Толщина не должна превышать диаметр отверстия.
420 Pages | Valable jusqu’au 12/2023 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
