Dynabrade - Industrial Katalog Page 307
Offre client commercial**Meilleures ventes de Dynabrade Europe Sarl
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
307 Collet Router Bits Ø3/8" ( 9.5 mm) mandrel max. Round abrasive discs Ø9" (230 mm) max. Routers Rotary Sanders Required on both sides of wheel. Loose blotters must be replaces when mounting a new wheel – – – Not Required Abrasive disc must not exceed 1/4" (6 mm) overhang Retaining nut secures abrasive disc Outer Flange Spindle Blotter Blotter Reinforced Cut-Off Wheel Clearance Washer (Optional) Backup Pad Spindle Collet Cap Collet Cap Mounted Wheel/Burr Cone or Plug Retaining Nut Abrasive Disc 1/4" Max. Overhang on Abrasive Sanding Disc Router Cutter Mandrel should be fully inserted into Collet Insert Router Cutter Base Plate Wheel/Burr Mandrel should be fully inserted into Collet Insert, no less than 1/2" (13mm). Excessive Overhang Reduces Bit MOS, Refer to ANSI B7.1 Standards Collet Insert Right Angle Housing Collet Body Collet Insert Clearance Collet Body Driving Flange with Straight Unrelieved Surface Blotter Spindle is shorter than hole providing proper clearance. Lip Feature Driving Flange Safety Guard Spindle Adapter Diagram Proper Mounting Procedure Always refer to ANSI B7.1, B186.1 and EN 792 for detailed requirements. Not Required Not Required Not required where the work offers protection or where the size does not exceed 2" (51 mm) • A guard cover is not required • Lip Feature must extend past face of wheel • Lip Feature • 180° minimum Operator Protection Guard Requirements – Excessive overhang reduces MOS See safety standard tables See safety standards for proper Spindle thread length – Additional Safety Must use Base Plate to control cut – – Straight relieved flange matching diameter to Drive Flange Blotters Required between flange and wheel Outer Flange PRODUCT & SAFETY INFORMATION NOTE: Intended for general reference use only. Backup pad supports abrasive disc Collet Straight unrelieved flange 1/3 of wheel diameter minimum Straight relieved flange 1/4 of wheel diameter minimum Driving Flange All Mounted Wheels and Burrs Ø1" (25 mm) to Ø3" (75 mm) Up to 4" (100 mm) diameter equal to or less than 1/8" (3 mm) thick Abrasive Size Die Grinders Type 16 - 19 Cone or Plug Wheels Reinforced Straight Wheels (formerly Type 1 cut-off) Type 41 Abrasive Type Mounting Features Safety Guidelines For Various Abrasive Power Tools
316 Pages | Valable jusqu’au 07/2026 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
