Bosch Air tools for industry catalog Page 8
Offre client commercial**Meilleures ventes de Bosch Blau
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
8 | Drills, rotary hammers | Selection guide 1 Selection guide Drills Drills Part number Choosing a drill is based on two No-load speed (rpm) Page criteria: ▶ the drilling diameter Cutting speed (m/min): ▶ the recommended cutting 120-watt drill controlled speed of the material you are 0 607 154 101 working on 3,200 10 (see page 14). 400-watt drill In the table, the optimal cutting speeds and drilling diameters for some common materials are allocated to the individual drill uncontrolled 0 607 161 100 2,560 10 0 607 161 102* 2,560 10 0 607 161 101 1,200 10 0 607 161 103* 1,200 10 models. 180-watt drill These recommendations are based on the speeds for HSS twist uncontrolled 0 607 153 520 3,700 10 0 607 153 523* 3,700 10 drill bits. If nothing is specified, the required drilling diameter is outside the capacity of the standard 400-watt drill uncontrolled 0 607 161 500 2,560 10 0 607 161 504* 2,560 10 The table shows which drill bit 0 607 161 501 1,200 10 sizes the individual models can 0 607 161 505* 1,200 10 chuck. 0 607 161 502 800 10 0 607 161 506* 800 10 ally been assigned the maximum 0 607 161 503 640 10 drilling diameters for steel, deter- 0 607 161 507* 640 10 accept and the drilling speeds. The individual tools have addition- mined in tests. * with keyless chuck To ensure that a sufficient cutting speed is always achieved, some materials should be pre-drilled as of the following drilling diameter: ▶ Steel up to 600 N/mm2 as of 8 mm ▶ Steel over 600 N/mm2 as of 6 mm ▶ Cast iron up to 180 N/mm2 as of 10 mm ▶ Cast iron up to 300 N/mm2 as of 8 mm
116 Pages | Valable jusqu’au 06/2024 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
