BILZ - ThermoGrip ® Schrumpfspannfutter Page 7
Offre client commercial**Meilleures ventes de BILZ WERKZEUGFABRIK
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Vorweite – das ThermoGrip® Markenzeichen Counterbore – the ThermoGrip® Brand n n n n n n Vorzentrierung des Werkzeugs für einen automatisierten Schrumpfprozess 15 % – 20 % geringerer Wärmebedarf bei der Erhitzung – materialschonend Optimales Ausschrumpfen von HSS Schäften Precentering of the tool for an automatic shrinking process 15 % – 20 % less heat needed during heating – low wear Optimal shrinking out of HSS shanks Vorweite Counterbore Die patentierte Bilz Vorweite erlaubt problemlose Werkzeugwechsel The patented Bilz counterbore allows problem free tool change Hot Spot mit grafisch dargestellter Weitung Hot Spot produces symmetric widening Infokasten Information Das Bild oben zeigt einen Querschnitt eines induktiv erhitzten Schrumpffutters. In der Spulenmitte ist die Magnetfeldstärke am größten, weshalb sich dort die Futteroberfläche mehr als an den Randbereichen der Spule erwärmt. Durch diesen „Hot Spot“ ergibt sich eine unterschiedliche Temperatur entlang des Futters. Dadurch weitet sich das Futter um wenige Mikrometer in der Mitte stärker nach außen. Das Futter ist somit am Hot Spot immer minimal mehr geöffnet als am Bohrungseingang. Die zylindrische Vorweite überbrückt diesen kritischen Punkt sicher bei reduziertem Energiebedarf. Diese materialschonende Erwärmung bewirkt eine längere Lebenszeit der Schrumpffutter. 8 ThermoGrip® The picture above shows the cross section of an inductively heated shrink chuck. The surface of the chuck mainly heats the Hot Spot area very quickly. This area is situated in the middle of the coil spindle. Since the temperature is always higher on the surface of the chuck than in the inner part, the chuck opens by micrometres – similar to a banana – slightly outwards. Because of this, the chuck is always slightly more open at the Hot Spot than at the boring entry. The cylindrical counterbore bypasses this critical area securely at reduced energy requirement. Due to this low wear heating process, a longer tool life of the shrink chucks is guaranteed.
101 Pages | Valable jusqu’au 07/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
