BILZ - ThermoGrip ® Schrumpfspannfutter Page 13
Offre client commercial**Meilleures ventes de BILZ WERKZEUGFABRIK
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
hors Expédition
Erklärung der Piktogramme Illustration of the Pictograms ≤ 3µm Rundlaufgenauigkeit der ThermoGrip® Schrumpffutter Concentricity of the ThermoGrip® Shrink Chucks max. 8.000 max. 10.000 max. 12.000 max. 15.000 max. 18.000 max. 20.000 max. 24.000 max. 25.000 max. 30.000 max. 35.000 max. 36.000 max. 40.000 max. 42.000 max. 50.000 Max. zulässige Drehzahl Max. RPM G2,5/ 25.000* Wuchtgüte: Die Futter sind werkseitig feingewuchtet mit G2,5 bei 25.000 U/min, bei Futtern mit Masse > = 1 kg bzw. bei Futtern mit Masse < 1 kg mit Restunwucht < 1 g mm Balancing: The chucks are factory-made finely balanced with G2,5 at 25.000 rpm, for chucks with the mass of > = 1 kg; or chucks with the mass of < 1 kg with residual imbalance < 1 g mm CHIP Mit Datenträgerbohrung With data carrier bore coated Nichtrostend beschichtet Corrosion protected ( coated ) Für tiefe Kavitäten geeignet – speziell für den Gesenk- und Formenbau Suitable for deep cavities – especially for the mold and die industry Vibrationsdämpfung Vibration damping HSS Geeignet für HSS Schäfte ab Durchmesser 6 mm Suitable for HSS shanks from diameter 6 mm Für alle ThermoGrip® Schrumpffutter gilt: Werkzeugschafttoleranzen: Ø 3,4 = h4 | Ø 5 = h5 | Ø ≥ 6 = h6 Formular Sonderschrumpffutter direkt per QR Code: Form special shrink chuck directly via QR Code: DE 14 ThermoGrip® EN The following applies for all ThermoGrip® shrink chucks: Shank tolerance: Ø 3,4 = h4 | Ø 5 = h5 | Ø ≥ 6 = h6
101 Pages | Valable jusqu’au 07/2025 | Page précédente | Page suivante
Choisissez votre langue
Probleme juridique
Le fabricant est exclusivement responsable du contenu, des prix et des détails des articles et des offres présentés dans les catalogues. Sous réserve de modifications techniques et optiques du fabricant et sous réserve d’erreurs.
Formulaire de demande de produits spéciaux
Le service d’approvisionnement ToolTeam®
Vous recherchez des produits qui figurent dans le catalogue mais ne peuvent pas être achetés directement en ligne ?Notre service d’approvisionnement se fera un plaisir de vous faire une offre individuelle et sans engagement.
